Planex MZK-W04NU User Manual Download Page 29

Page: 29 / 82

MZK-W04NU

5.4.Firmware Management

You can upgrade the firmware of MZK-W04NU via Web Browser.

First, please go to the website: http://www.planex.net/support/index.

htm to download the latest firmware of MZK-W04NU. Be sure that the

downloaded firmware is stored in your PC

s disk and then click

Browse

ČŇ

to search for the firmware file which you just downloaded.

Click

Open

to use the firmware and then go back to the configuration

page, and click

Firmware Update

to start upgrading immediately.

It is recommended that you should save the settings before upgrading the

firmware.

It takes about 2~3 minutes to upgrade the firmware. When
upgrading, please do not turn off the power of MZK-W04NU.
A f t e r f i n i s h i n g u p g r a d i n g, M Z K-W04N U w i l l r e s t a r t
automatically.

Summary of Contents for MZK-W04NU



















































































Search results

Summary of Contents for MZK-W04NU

Reviews:

Brands by name

Popular brands

Planex MZK-W04NU, User Manual

Search results

Summary of Contents for MZK-W04NU

Reviews:

Brands by name

Popular brands