background image

 

Network Type 

Infrastructure

 – This operation mode requires the presence of an 

802.11 Access Point. All communication is done via the Access 

Point or Router.   

 

Ad-Hoc

 – Select this mode if you want to connect to another 

wireless station in the Wireless LAN network without through an 

Access Point or Router. 

 

 

TX Power 

If you want to lower the transmit power of the card for saving the 

power of the system, you can select the lower percentages from 

the list. The lower power will cause the lower signal strength and 

the coverage range. 

 

 

Ad Hoc Wireless Mode 

When the card is set in Ad Hoc (Peer to Peer Mode), you can 

designate the wireless connection mode for the Ad Hoc network.

802.11 B only

 – This card can be compatible with both 802.11g 

and 802.11b wireless stations. If there are only 802.11b wireless 

stations in the network, you can set the card to this mode. 

 

802.11 B/G mix

 – If you have a mix of 802.11b and 802.11g 

wireless stations in your network, it is recommended to setting the 

card to this mode. This mode is also the default setting. 

 

802.11 G only

 – This card can be compatible with both 802.11g 

and 802.11b wireless stations. If there are only 802.11g wireless 

stations in the network, you can set the card to this mode. 

 

 

Preamble 

The preamble defines the length of the CRC block for 

communication among wireless devices. This option is only active 

in the Ad Hoc network. 

 

There are two modes including Auto and Long Preamble. If 

“Auto“ mode is selected, the card will auto switch the preamble 

mode depending on the wireless devices the card is connecting 

to. 

 

 

RTS Threshold 

Minimum packet size required for an RTS (Request To Send). For

packets smaller than this threshold, an RTS is not sent and the 

packet is transmitted directly to the wireless network. Select a 

setting within a range of 0 to 2347 bytes. Minor change is 

recommended. 

 

 

Fragment Threshold 

The value defines the maximum size of packets; any packet size 

larger than the value will be fragmented. If you have decreased 

this value and experience high packet error rates, you can 

increase it again, but it will likely decrease overall network 

10

 

Summary of Contents for WL-U356R



































Reviews: