background image

 

 

1. Introduction 

1.1 Checklist 

Check the contents of your package for following parts: 

 

  Ethernet over VDSL Converter 

 

 Power Adapter 

 

 Telephone line 

 

  Cat.5 Ethernet Cable 

 

  Quick Installation Guide 

 

  User’s manual and utility CD 

 

  RS-232 Console cable(VC-101M only) 

If any of these pieces are missing or damaged, please 
contact your dealer immediately, if possible, retain the carton 
including the original packing material, and use them against 
to repack the product in case there is a need to return it to us 
for repair. 

 

1.2  Introduction to Ethernet over VDSL 

Converter 

The converter is a switching architecture with one RJ45 
10/100Mbps Fast Ethernet ports and one RJ11 symmetric 
Ethernet over VDSL port (symmetry means upstream and 
downstream rate are the same or similar). It is ideal for signal 
conversion by transmitting the Ethernet data from the 
standard twisted pair cable to the telephone cable and 
extending the distance. 

The Ethernet over VDSL combines the well proven Ethernet 
and VDSL technology to transmit the Ethernet format data by 
using VDSL signaling over the most widespread telephone 
wires and has no impact to current voice service. Therefore, 
it is very good for Internet building phone line network 
because every room or house could use the existing phone 
line to transmit data to the Internet and the whole building 

Summary of Contents for VC-1015



























Reviews: