Planet PL-501v2-EU User Manual Download Page 5

Chapter 1: Introduction 

Overview 

Thank you for purchasing PLANET 200M Powerline Ethernet Adapter. With 
Planet powerline communication products, your power outlets are no longer to be 
viewed only as power receptacles but also as network connection point. The PL-
501v2 is a Powerline to Ethernet Bridge with a RJ-45 Ethernet interface which 
directly connecting to your computer’s network card. With multiple outlets in 
almost every room, PL-501v2 allows you to use your existing electrical wiring to 
give your entire household or Office access to your network connection without 
the clutter of messy wiring around the house and Office. 

 

By using Planet‘s powerline communication products, you will not need to spend 
time and money to installing Ethernet cabling to share network. It is simply by 
plugging the PL-501v2 into the wall anywhere in the house or office. The 128-Bit 
AES data encryption improves the security and reliability, to protect the data 
leaked by someone else. Customers will not need to worry about the data will be 
leaked. The speed up to 200 Mbps data rate which provides customers the 
highest speed in powerline data transferring. This product is cost-effective, easy 
to install, and do not require any new wired. 
 
 

Features 

Š

  Direct attached to power outlets 

Š

  HomePlug AV compliant 

Š

  Connect 10/100 Ethernet network to Powerline network 

Š

  Up to 200Mbps data rate on the powerline 

Š

  Up to 200 meters between powerline nodes 

Š

  128-Bit AES link Encryption for security and reliability 

Š

  Co-existence with HomePlug 1.0 and HomePlug 1.0 Turbo 

Š

 Built-in QoS 

Š

  Throughout the whole house, just use your power circuit to access the 

Internet or PC network 

Š

  16 bridged devices per station 

Š

  IGMP snooping for multicast to multiple uni-cast mapping 

 
 

 

 

5

Summary of Contents for PL-501v2-EU


















Reviews: