manualshive.com logo in svg

Planet IHD-200PR, User Manual

Share
Download
Planet IHD-200PR User Manual Download Page 8

 

 

HDMI / Video Wall over IP with PoE

 

IHD-200PT / IHD-200PR

 

 

Easy Video Channel Matching through Network Configuration 

The IHD-200 PoE series network can be configured by a central computer over the 
same LAN within a certain distance. Fully leveraging the mature Gigabit Ethernet 
with 802.1Q VLAN function, multi-casting can be performed to allow more video 
source/senders in the network and be remotely managed. Just adjust and match 
video channel setting by the simple DIP switch in both the IHD-200PT and IHD-
200PR.  The video distribution is easily deployed through Plug and Play.

 

 

 

High Quality Output and Performance 

The IHD-200 PoE series supports Full HD 1080P, HDCP and Blu-ray quality, which 

have been commonly used for applications that require real-time high video 

resolution and transmission in long distance. It also contains security and noise 

immunity as well as HDMI with 2ch. audio (dts.) functions to offer the superior video 

distribution.

 

 

Summary of Contents for IHD-200PR























































Reviews:

No comments

Brands by name

Popular brands

Load more brands