Planet ICA-120 Page 30 User Manual Download

Page: 30 / 77

Setting Menu

This function is detail setting for camera that only available for
user logged into camera as administrator.

Item

Action

Network

Configure Network settings such as Wireless,
DHCP, DDNS, 3GPP, PPPoE and UPnP

Camera

Adjust camera parameters

System

Configure system information, date & time,
maintenance, and view system log file.

Video

Configure bit rate and frame rate of video
profiles

Audio

Configure audio parameters

User

Setup user name, password and login privilege

E-Mail

Setup E-Mail configuration

Object Detection

Setup Object detection

Event Server

This device is a client site and configure
information to upload images to server

Event Schedule

Configure the schedule while event triggered

Streaming Protocol

User can select proper streaming protocol according to
networking environment.

Language

The device could provide multiple languages to meet customer’s
requirement.

Video Information

Display video information including video format, resolution, frame
rate and bit rate.

Summary of Contents for ICA-120














































































Search results

Summary of Contents for ICA-120

Reviews:

Related manuals for ICA-120

Brands by name

Popular brands

Planet ICA-120, User Manual

Search results

Summary of Contents for ICA-120

Reviews:

Related manuals for ICA-120

Brands by name

Popular brands