background image

                                                                                                 

Wizard Page 2: LAN Setting 

This page is about the select of Static IP or DHCP ON.   

 

LAN:

 

You can configure this IR IP Camera to obtain its address automatically or 
manually assign. If there is a DHCP server in your network environment and 
you select “

DHCP ON

”, IR IP Camera can automatically obtain an IP address. 

If you don’t have DHCP server or you want to use fixed IP address, please 
select “

Static IP

” and fill in the following fields with proper parameters. 

IP Address:

 

IP address is a unique number for identifies this device on the WAN or LAN. 
These numbers are usually shown in groups separated by periods, for 
example: 192.168.0.200 

Subnet Mask:

 

Subnets allow network traffic between hosts to be separated based on the 
network's configuration. In IP networking, traffic takes the form of packets. IP 
subnets advance network security and performance to some level by 
organizing hosts into logical groups. Subnet masks contain four bytes and 
usually appear in the same "dotted decimal" data. For example, a very 
common subnet mask in its binary demonstration 11111111 11111111 
11111111 00000000 will usually be shown in the corresponding, more 
readable form as 255.255.255.0. 

Def. Gateway:

 

A gateway is a piece of software or hardware that passes information 
between networks. You'll see this term most often when you either log in to 
an Internet site or when you're transient email between different servers. 

DNS1:

 

When you send email or position a browser to an Internet domain such as 
xxxxx.com, the domain name system translates the names into IP addresses. 
The term refers to two things: the conventions for naming hosts and the way 
the names are control across the Internet. 

DNS2:

 

The same function as DNS1. It is optional, not necessary 

Note: 

If no IP address is assigned after 30 seconds, the IR IP Camera will work with its default IP 

 15 

Summary of Contents for ICA-108













































































Reviews: