Planet FT-902 User Manual Download Page 28 | Manualshive

Page: 28 / 40

Planet FT-902 User Manual Download Page 28

-25-

4.6 Statistics

The Port Statistic page displays the status of packet count from copper port and fiber port. The Port statistics screen in
Figure 4-12 appears.

Figure 4-12

Statistics screen

The page contains the following fields:

•

Port

Indicate the Copper port and Fiber port

•

Octets

Displays the number of octets received on the interface since the device was last
refreshed. This number includes bad packets and FCS octets, but excludes framing
bits

•

Drop Events

Which displays the number of dropped events that have occurred on the interface
since the device was last refreshed

•

Pkts

Displays the number of packets received on the interface, including bad packets,
Multicast and broadcast packets, since the device was last refreshed

•

Broadcast Pkts

Which displays the number of good broadcast packets received on the interface
since the device was last refreshed. This number does not include Multicast packets

•

Multicast Pkts

Displays the number of good Multicast packets received on the interface since the

«
...
26
27
28
29
30
...
»

Summary of Contents for FT-902









































Reviews:

No comments