Planet ATA-150 Series User Manual Download Page 39 | Manualshive

Page: 39 / 50

background image

Save / Reload Settings

This page allows you save current settings to a file or reload the settings from the file which was saved

previously. Besides, you could reset the current configuration to factory default.

Save Settings to File

Save current settings to a file.

Load Settings from File

Browse a file and upload to reload settings.

Reset Settings to Default

Press

Reset

will clean all current configurations and return to

default values.

Password Setup

This page is used to set the account to access the web server of ATA. Empty user name and password

will disable the protection.

User Name

Enter user name.

New Password

Input password for this user.

Confirmed Password

Confirm password again.

Reboot

Press Reboot to reboot system. Please wait for a few minutes and reload web page again.

-

39

-

«
...
37
38
39
40
41
...
»

Summary of Contents for ATA-150 Series



















































Reviews:

No comments

Related manuals for ATA-150 Series

Brand: Linksys Pages: 2

PowerGrid-9171n

Brand: Comtrend Corporation Pages: 55

Brand: Solisto Pages: 12

Brand: Solwise Pages: 25

Brand: TP-Link Pages: 75

Brand: Renesas Pages: 2

Brand: Quintum Pages: 58

Brand: Jabra Pages: 2

FRITZ!Powerline 510E Set

Brand: AVM Pages: 38

Artisan 700 Series

Brand: Epson Pages: 2

Artisan 800 - All-in-One Printer

Brand: Epson Pages: 106

Artisan 700 Series

Brand: Epson Pages: 40

ActionTower 3000 Computer

Brand: Epson Pages: 137

Artisan 700 Series

Brand: Epson Pages: 145

Artisan 800 - All-in-One Printer

Brand: Epson Pages: 2

Brand: Uplift Desk Pages: 2

Brand: Dynex Pages: 1

BlackBird SemiPro 3xHS

Brand: Kvaser Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands