manualshive.com logo in svg

Planet Networking & Communication IPM-16120, User Manual

Share
Download
Planet Networking & Communication IPM-16120 User Manual Download Page 25

 

IP-based 16-port Metered Power Distribution Unit 

IPM-16120 

- 

25

 - 

Parameters 

Description 

this function is normal. 

 

4.2.3 

SMS Server 

In this section, user can set up the warning message and info to the SMS server. The protocol here is 

supported by many SMS suppliers’ (ISP) API. System will send out account, password, time, and 

related info via HTTP to the SMS server of ISP supplier or preset SMS server.

 

 

 

Parameters 

Description 

Host 

Host IP address of SMS Server. 

Transmission Mode 

Follow ISP suppliers’ rules to send out short message via GET or 

POST protocol to sender’s server. 

Device Name 

The name user wants to reveal. 

Account

 

The account to fill in when sending SMS. The same as 

@@ACCOUNT@@.

 

Password 

The password to fill in when sending SMS. The same as 

@@PASSWORD@@.

 

Message Format 

We provide “auto bring-in” system with username, password, 

number, main host and message content. 

SMS Test 

After setting up the above info, you can send a test mail to make sure 

this function is normal. 

 

Summary of Contents for IPM-16120












































Reviews:

No comments

Brands by name

Popular brands

Load more brands