manualshive.com logo in svg

Planet Networking & Communication FRT-415N, User Manual

Share
Download
Planet Networking & Communication FRT-415N User Manual Download Page 79

User Manual of FRT-415N 

 

 

79

5.5.4 DDNS 

Click

 DDNS 

in the left pane and the page shown in the following figure appears. This page is used to configure the 

dynamic DNS address from DynDNS.org, TZO, PHDNS, NO-IP or PlanetDDNS. You can add or remove to 
configure dynamic DNS. The Planet DDNS is free for customers 

 

Figure 5-59 

DDNS 

 

The following table describes the parameters: 

Field 

Description 

DDNS provider 

Choose the DDNS provider name. You can choose DynDNS.org, TZO, 
PHDNS, NO-IP or Planet. 

Host Name 

The DDNS identifier. 

Interface 

The WAN interface of the fiber router. 

Enable 

Enable or disable DDNS function. 

Username 

The name provided by DDNS provider. 

Password 

The password provided by DDNS provider. 

 

First of all, please go to 

http://www.planetddns.com

 to register a Planet DDNS account, and refer to the FAQ 

(

http://www.planetddns.com/index.php/faq

) for how to register a free account. 

Summary of Contents for FRT-415N






















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands