background image

ENG  

PLANAR-8DM 

 

 

 

 

 

17 

 

-

 

at minimum duty,  

-

 

at maximum duty.  

Launch  procedure  begins  with  quick  purging  of  the  combustion  chamber.  Next,  the 

ignition process starts, and the heater reaches the required operation mode.   

9.5

 

Switch  the  heater  off.  If  the  heater  is  switched  off,  gas  supply  stops,  and  the 

combustion chamber and the heat exchanger are purged with air.   

9.6

 

Start the heater with the vehicle engine on and check functioning of the heater.   

  

Attention!   

 

1

 

During the first launch after installation, good practice is to fill the fuel line 

up  to  the  heater  intake  nozzle  with  air  using  the  booster  pump.  In  case  no  booster 
pump is available, launch the heater several times to ensure the fuel line is full.  

 

2

 

Remember  that  in  case  the  heater  fails  to  start  in  the  heating  mode,  the 

control unit automatically repeats the launch attempt.

 

 

 

 

10

 

Recommendations  

10.1  To  ensure  reliability  of  heater  operation,  start  it  up  once  every  month  for  5–10 

minutes (including during the warm season if the heater is not in use). This is necessary to 
remove viscous film deposits from moving parts of the fuel pump. Failure to do so may lead 
to a heater malfunction.  

10.2  Operation  of  the  heater  depends  on  fuel  used.  Use  fuel  compatible  with  GOST 

305-82  and  with  ambient  temperature  (see  table  10.1).  Fuel  mixtures  are  also  allowed,  if 
compliant with Fig. 10.  

Table 10.1 

 

Ambient temperature, °С

 

Fuel (mixture) type

 

Above 0 

 

Diesel fuel L-0.2-40 or L-0.2-62 under GOST 305-82

 

0 to minus 5 

 

Diesel fuel Z-0.2 minus 35 under GOST 305-82

 

Minus 5 to minus 20 

 

Diesel fuel Z-0.2 minus 35 under GOST 305-82 or 
diesel fuel Z-0.2 minus 45 under GOST 305-82

 

Below minus 20 

 

Diesel fuel А-0.4 under GOST 305-82

 

 

 

Summary of Contents for PLANAR-9D-12





















Reviews: