Planar PE150 Owner'S Manual Download Page 10

 

Chapter 3 Technical Information 

Specifications 

LCD Panel 

 

Size 

15.0" (38 cm) 

Display Type 

Active matrix color TFT LCD 

Resolution 

1024 x 768 

Display Area (mm) 

304 x 228 (H x V) 

Brightness 200 

cd/m

2

 (typical) 

Contrast Ratio 

400:1 (typical) 

Response Time 

35 ms (typical) 

Viewing Angle 

 

Vertical: -55° ~ +45° 
Horizontal: -65° ~ +65° 

 
Display Colors  

          

16.7M with FRC or Dithering

 

 

Video 

Input Signal 
Input Impedance 
Polarity 
Amplitude 
Multi-mode Supported 

Analog RGB 0.7Vp-p 
75 Ohm ± 2% 
Positive, Negative 
0 - 0.7 ± 0.05 Vp 
Horizontal Frequency: 24 ~ 61 KHz 
Vertical Frequency: 56 ~ 75 Hz 

Control   

Power

 

On/Off switch with LED indicator

 

 
Power Management 

Mode

 

Power 

AC Input

 

LED Color

 

On 

25W maximum 

240 VAC 

Green 

Standby 

5W maximum 

240 VAC 

Yellow 

Suspend 

5W maximum 

240 VAC 

Yellow 

Off 

5W maximum 

240 VAC 

Yellow 

DC Power Off 

5W maximum 

240 VAC 

Dark 

Disconnected 

5W maximum 

240 VAC 

Yellow: Standby, Suspend, Off 

Dark: DC Power off 

 
*  Meeting VESA DPMS requirements measured from AC Input end of AC adapter.  

 

8

Summary of Contents for PE150














Reviews: