background image

 

QUICK LINKS

 

Contents

Index

Regulatory Compliance

Product Information

Warranty

 

GETTING STARTED

 

About the Battery System

Locate Battery Housing

Identify Connector Ports

Install  Battery Fuses

 

USING THE BATTERY

 

Charge Battery

Set Up Power Management

 

MAINTAINING THE BATTERY

 

Replace Battery

Troubleshooting

 

APPENDIXES

 

Battery Disposal

Specifications

 

iv

 

Invitium Battery System BAT-24CM

 

Product Information

 

Safety guidelines

 

The Invitium battery system is designed to ensure both the highest level of 
product quality and safety for the user. To maintain both quality and safety, 
follow the guidelines and instructions in this manual.

 

 

Use the battery system only as intended.

 

 

Do not place the battery system near a window. Exposing the system to rain,

 water, moisture or constant direct sunlight can severely damage it. 

 

 

Refer all servicing to qualified personnel to maintain your warranty. 

The battery system has no internal user-serviceable parts. 

 

 

Do not cover or obstruct any venting holes on the battery system.

 

 

Store the battery system within –20 to +65 degrees Celsius. Storing the system 

outside that temperature range could result in permanent damage.

 

 

 If any cord or cable is frayed or damaged, replace it immediately with another of 

the same type and rating as supplied by Planar. The safety and regulatory listing and 
certifications are based on cables supplied by Planar.

 

 

Use and maintain the safety ground plug set (power cord) included with the unit. 

 

 

After battery system installation, secure all electrical cords to prevent 

accidental damage.

 

 

To clean the exterior chassis of the battery system, follow the UL 2601 standard for 

use in a hospital environment. See

 cleaning guidelines

 for more information.

 

 

Before cleaning the chassis, disconnect the unit from its power source.

 

 

Be careful when moving the battery system to a different location. 

Use original packaging whenever possible.

 

Warning

 

• Equipment is not suitable for use 

in the presence of a flammable 
anesthetic mixture with air, 
oxygen, or nitrous oxide.

• The Invitium battery system 

may be energized or operational 
even when disconnected from 
the AC power source.   

• If the Invitium battery system has 

been exposed to liquid, has been 
dropped, or if its base has been 
damaged, it may pose a shock or 
fire hazard. Immediately unplug it 
and contact customer service for 
assistance.

• Use care in handling the battery if 

any leakage is observed. Avoid 
skin contact and wash any areas 
that come in contact with this 
material immediately.

• Plug the battery system only into 

a grounded power outlet. 

Summary of Contents for BAT-24CM

































Reviews: