3
Control menu contents
Sets the base DMX address from which the control channels will begin.
Shows the main processor software revision. No changes are possible within
this option. Press
while viewing this option to see the software sub-revision.
Shows the display controller software revision. No changes are possible within
this option.
Selects the primary internal chase effect. See Chase effects for descriptions.
Select
MODE
>
EF M
to show the selected chase.
Selects the cross fade speed between the steps of the selected
C1
chase effect.
Selects the speed of the selected
C1
chase effect.
Selects the master intensity level of chase effects
C1
and
C2
.
Selects the secondary internal chase effect. See Chase effects for descriptions.
Select
MODE
>
EF M
to show the selected chase.
Selects the cross fade speed between the steps of the selected
C2
chase effect.
Selects the speed of the selected
C2
chase effect.
Sets the red intensity. Select
MODE
>
MANU
(manual) to show the result.
Sets the green intensity. Select
MODE
>
MANU
(manual) to show the result.
Not available when
PERS
>
RES
is set to
1CH
.
Sets the blue intensity. Select
MODE
>
MANU
(manual) to show the result.
Not available when
PERS
>
RES
is set to
1CH
.
Sets the cool white intensity. Select
MODE
>
MANU
(manual) to show the result.
Not available when
PERS
>
RES
is set to
1CH
.
Sets the warm white intensity - only available when
PERS
>
RES
is set to
5CH
.
Select
MODE
>
MANU
(manual) to show the result.
Selects number of channels required to control all emitters. Options range from 1
through 4, 5 and 61. Emitters are grouped together accordingly (see channel layouts).
Determines whether this fixture will act as a master controlling others.
When controlled via DMX this fixture must be set to
SLAV
.
DMX
and
16bt
modes only. When set
ON
this enables 16-bit master intensity control
(2 x 8-bit channels). For 8-bit control use the high channel alone (see channel layouts).
DMX
mode only. When set
oN
, allows you to determine the dimmer type via DMX.
This channel is always the final DMX channel. See ‘Changing dimmer curve via DMX’.
DMX
mode only. Rotates DMX channel to emitter mapping by 90 degree increments
to allow for units mounted on the side or inverted. See ‘Rotating the emitter layout’.
When set
oN
, this option scrolls through the primary colours at power on to
demonstrate correct operation of the emitters.
Determines the intensity of the four digit control panel display. Values range from
0 (dimmest) to 15 (brightest).
When set to
AOFF
, the control panel display will blank out 25 seconds
after the menu is exited. The data dot indicator will remain active.
Provides a choice of two dimmer responses (
FINE
or
TUNG
) to suit requirments.
See ‘Dimmer curve options’ for descriptions of each option.
RGBWW control using an external DMX control input.
PERS
>
MINT
set to
ON
provides 16-bit master intensity control. No chase effects are selectable.
Displays the resulting RGBWW levels that are set via the
MAN
section of the internal
menu. External DMX control is not possible in this mode.
Displays the chase effect(s) determined within the
PROG
section. External DMX
control is not possible in this mode.
DMX Ch1 to 4: RGBW colour mixing, Ch5 to 7:
C1
Effect, Speed & Xfade,
Ch8 to 10:
C2
Effect, Speed & Xfade, Ch11 & Ch12: 16-bit master intensity.
DMX Ch1 to 5: RGBWW colour mixing, Ch6 to 8:
C1
Effect, Speed & Xfade,
Ch9 to 11:
C2
Effect, Speed & Xfade, Ch12 & Ch13: 16-bit master intensity.
DMX Ch1 to 61: RGBWW colour mixing, Ch62 to 64:
C1
Effect, Speed & Xfade,
Ch65 to 67:
C2
Effect, Speed & Xfade, Ch68 & Ch69: 16-bit master intensity.
16bit RGBWW control using two DMX channels per colour.
PERS
>
MINT
set to
On
provides 16-bit master intensity control. No chase effects are selectable.
