3
Bright
Dark
4
-cylinder
5
6
8
3
2
1
Special
A
0
2
3
1
1
0
1
3
2
2
OFF
ON
SETTING
A
Cylinder Number Setting
SETTING
D
Shift lamp brightness setting
Press for 5 seconds
Make setting to change the shift lamp brightness.
With no operation
for 2 seconds
Reference: If the engine is a two cycle engine, multiply the number of cylinder by two.
(e.g., For a two-cycle three-cylinder engine the setting would be six.)
Set the cylinder number for the car being used.
The number of cylinders is set by the shift lamp pattern.
Press the
switch once
OPENING DEMO
OPENING DEMO
OPENING DEMO
Tachometer display
With no operation
for 2 seconds
Press the switch
for 5 seconds
Press the
switch
Press the
switch
With no operation
for 2 seconds
Press the switch
for 5 seconds
Key ON
(engine not running)
Lamp Off
SETTING
E
Switching the signal level
Press for 5 seconds
6
7
8
Tachometer display
9
1
5
4
3
3
1
2
4
5
4
2
3
6
7
1
METER INSTALLATION
Install in an easy-to-view location.
SETTINGS
After finishing the installation, make various settings.
(The factory default setting is for a
four-cylinder engine)
Cylinder display
Turn
1
2
3
4
5
6
8
Special
A
Number of
cylinders
NISSAN (FAIRLADY Z Z33)
・
MAZDA (ATENZA and others)
MAZDA (RX-8)
・
SUBARU (early type of PLEO and others)
Three-cylinder
Four-cylinder, Rotary engine (RX-7)
Five-cylinder
Six-cylinder
Eight-cylinder
Some models of NISSAN
Car models
Shift lamp
Pillar holder for ø60
PH-60
If you wish to open holes to fasten
the unit to the pillar or column
cover, please purchase and use
the separately sold pillar holder.
Pillar
holder
A pillar
Screw
hole
Can be mounted in various
places
Mount almost anywhere using the
double-sided tape. After mounting it
is possible to for easy-reading.
Press the switch to change the
pattern and set to the proper one.
While the tachometer is being
displayed, press the switch for long.
While the tachometer is being
displayed, press the switch for long.
After 1.5 seconds the shift
point will be shown and after 5
seconds All lamps will light
All shift lamps
will light
On the dashboard
On the steering
column cover
Meter dimensions
(unit; mm)
Patterns for cylinder settings display
= On
= Off
= Blink
The lamps blink red
The needle will show “1”or“2”
The lamps blink red
The needle will show the
set shift point
Changes are only necessary for those car models listed below.
NISSAN (FAIRLADY Z Z33)
/
MAZDA (after 2002)
/
MITSUBISHI (COLT and others)
/
SUBARU (early type of PLEO and others)
Note: See the “Wiring Chart” for details.
Press the
switch once
SETTING
B
Peak reading display and re-set
Peak reading
display
Press
1
Tachometer display
5
2
Press the switch
for 2 seconds
3
Pressing the switch will re-set the
peak reading.
The needle will show “0”
4
All shift lamps will light
1
=
If the generic car
2
=
If the level is small
Press the
switch
5
Fasten using the
double-sided tape.
( O n t o p o f t h e
s t e e r i n g c o l u m n
cover or dashboard)
Place the stand’s holder band around the back of the meter.
Note: If you cannot get the band around the meter, loosen
the hexagonal bolt and expand the band.
After getting the band in place, tighten the hexagonal bolt to
secure the band.
①
②
Wrap the cushion tape around the
base of the meter and forcibly insert
into the 60 mm hole in the panel.
A
Install with the adjustable stand
B
Installation with the
cushion tape
Hexagonal bolt
with washer
Holder band
Clean to remove
oil & dust
Double-sided tape
(included)
Hexagonal
bolt
ø60
ø65
30
15
1. Installing the adjustable stand
Bend the stand to securely fit the place of installation.
Clean the surface; removing all oil or dust.
Fasten using the double-sided tape.
Note: Please be sure about where you wish to install the
meter, as it is not advisable to reuse double-sided tape.
①
②
③
After deciding the
position and angle of
t h e m e t e r f a c e ,
fasten the hexago-
n a l b o l t s o n b o t h
sides to secure.
④
2. Installing to the car
Panel
Cushion
tape
2
While holding the switch, start
the engine within 5 seconds.
ENGINE
START
SETTING
C
Shift Point Setting
Press for 1.5 seconds
Tachometer display
With no operation
for 2 seconds
Press the switch
for 1.5 seconds
Press the
switch
Each pressing of the switch will
raise, the setting 200 rpm; at 9000
rpm it will return to 3000 rpm.
3
2
4
1
5
The lamps blink red
The needle will show the
set shift point
While holding down the switch,
change the RPM setting
Make RPM setting for turning on the shift lamp. (setting range : 3000–9000 rpm)
Note: By continually pressing down on the switch the
needle will move to 9000 rpm.
2 steps
⇒
See
SETTING E
for details.
PREPARATION
Please check the number of cylinders and cycles for the model car being used.
Press the switch during the key
switch OFF (meter light off)
During meter light Off
Each pressing will change
the brightness.
Set the signal detection level by
pressing the switch to change the
needle position to the correct setting.
While the tachometer is being
displayed, press the switch once.
Note: For one and two cylinder engines,
set the signal level switch to two.
