Pittsburgh Automotive 68048 User Manual Download Page 4

SKU 

68048, 6049, 6056

 

For technical questions, please call 

1-800-444-3353 

Page: 

3

7.  Center the vehicle’s lifting point(s) on the saddle of the 

jack stand(s).  Set the jack stand(s) according to the 

manufacturer’s instructions, making sure that they lock 

securely into position.

Note: 

Always set both Jack Stands at the same height.

8.  Slowly turn the Handle counterclockwise to lower the 

vehicle onto the saddle(s) of the jack stand(s). Then, 

turn the Handle firmly clockwise to close it.

Lowering

1.  Carefully remove all tools, parts, etc. from under  

the vehicle.

2.  Position the Saddle under the lifting point. Turn the 

Handle firmly clockwise and raise load high enough 

to clear the jack stands, then carefully remove jack 

stands.

3.  Slowly turn the Handle counterclockwise (never more 

than 1/2 full turn) to lower the vehicle onto the ground.

4.  Lower the Jack completely.  Then, store in a safe, dry 

location out of reach of children.

Inspection, Maintenance, & Cleaning

  Procedures not specifically explained in this 

manual must be performed only by a qualified 

technician.

To prevent serious injury from tool failure: 

Do not use damaged equipment.  If abnormal noise or 

vibration occurs, have the problem corrected before further 

use.
1.  Before each use, inspect the general condition of the 

Jack.  Check for broken, cracked, or bent parts, loose 

or missing parts, and any condition that may affect the 

proper operation of the product.  If a problem occurs, 

have the problem corrected before further use. 

Do not use damaged equipment.

2.  Before each use, thoroughly test the Jack for proper 

operation prior to its actual use.  If the Jack appears 

not to be working properly, follow Bleeding instructions 

on page 2.

3.  Change the hydraulic oil at least once every three 

years:

A.  With the Jack fully lowered, remove the Oil Filler 

Plug on the side of the Housing.

B.  Tip the Jack to allow the old hydraulic oil to drain 

out of the Housing completely, and dispose of 

the old hydraulic oil in accordance with local 

regulations.

C.  With the Jack upright, completely fill the Housing 

with a high quality hydraulic oil (not included) until 

the oil is 1/4″ below the fill hole.

D.  Open the valve by turning the Handle 

counterclockwise and pump the Handle to bleed air 

from the system.

E.  Recheck oil level and re-fill as needed. 
F.  Reinstall the Oil Filler Plug.

7.  Wipe dry with a clean cloth. Then, store the Jack in 

a safe, dry location out of reach of children and other 

non-authorized people.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that 

its products meet high quality and durability standards, 

and warrants to the original purchaser that this product 

is free from defects in materials and workmanship for 

the period of 90 days from the date of purchase. This 

warranty does not apply to damage due directly or 

indirectly, to misuse, abuse, negligence or accidents, 

repairs or alterations outside our facilities, criminal activity, 

improper installation, normal wear and tear, or to lack of 

maintenance. We shall in no event be liable for death, 

injuries to persons or property, or for incidental, contingent, 

special or consequential damages arising from the use 

of our product. Some states do not allow the exclusion or 

limitation of incidental or consequential damages, so the 

above limitation of exclusion may not apply to you. THIS 

WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER 

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE 

WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must 

be returned to us with transportation charges prepaid. Proof 

of purchase date and an explanation of the complaint must 

accompany the merchandise. If our inspection verifies the 

defect, we will either repair or replace the product at our 

election or we may elect to refund the purchase price if we 

cannot readily and quickly provide you with a replacement. 

We will return repaired products at our expense, but if we 

determine there is no defect, or that the defect resulted 

from causes not within the scope of our warranty, then you 

must bear the cost of returning the product.
This warranty gives you specific legal rights and you may 

also have other rights which vary from state to state.

Summary of Contents for 68048











Reviews: