PITSOS WXP801B5, Instruction Manual, Page: 8 / 8

a
żƚƥƛƚƣƞƩƕ
ø
2
ƞ›Ƣ›ƤƖƨ
ƧƖƛ
ƚƤƥƚ
›Ʃƴ›ƤƭƫƠ
ƫƭƦơƞƬƢƣƕ
ø
2
ƞ›Ƣ›ƤƖƨ
ƧƖƛ
ƚƤƥƚ
ƞƭ›ƚơƗ
ø
2
ƞ›Ƣ›ƤƖƨ
ƧƖƛ
ƚƤƥƚ
ơƑƠƠƞƢƖ
ä
ø
ƣƒƗƘƖƠơƖ
ƧƨƱƬƞơƤ
ƑƢƨƠƜƧƜ
ƉƢƣƢƚƣƖƪ
ƌƭƫƣƞƭƖƪ
ƐƤƥ
ſơƦƢƣƗƪ
ƉƝƨƵ
ŻơƠƦƶƦ
ƅƚƥƘƚƪ
ƊƨƬƚƥƨƵ
ƄƠƮƢƫƢƕ
ŻơƗƦƚ
żƚƥƛƚƣƞƩƕ
żƚƥƛƚƣƞƩƕ
żƚƥƛƚƣƞƩƕ
żƚƥƛƚƣƞƩƕ
żƚƥƛƚƣƞƩƕ
ƫƭƦơƞƬƢƣƕ
ƞƭ›ƚơƗ
ơ ƕƤƤƢƦƚ
żƚƥƛƚƣƞƩƕ
ŤƂƍƃƂƋƆƑŽ
ƒ
ƎƂƑƏƈ
›ƂƝƓƈ
a
1
ŲƌƝƓƈ
2 ƏžƃƄƂƌƍƂ
1 ŲƌƝƓƈ
c ƓƔƝƘƊƍƐ
a
2 ƏžƃƄƂƌƍƂ
c ƓƔƝƘƊƍƐ
a
a
ŽƎƔƌƈƓƈ
ƓƔƝƘƊƍƐ c ŽƎƔƌƈƓƈ
11
What to do if ...
ʑ
Water is leaking out. – Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed. – Start/Pause not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
a page 10.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened. – Safety function active. Wait approx. 2 minutes.
ʑ
Programme does not
start. – Start/Pause selected?
– Washing machine door closed?
ʑ
Detergent solution is not
drained. – Clean the detergent solution pump a page 10.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum. – Not a fault - water below the visible area.
ʑ
Unsatisfactory spin
result.
Laundry wet/too damp. – Not a fault - the unbalanced-load detection system has cancelled
the spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the
drum.
ʑ
Spin cycle performed
several times. – Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment
~c for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
–> page 9 .
ʑ
Odour formation in the
washing machine. – Run programme
ŤƂƍƃƂƋƆƑŽ
( Cottons) 90 °C without laundry.
Use standard detergent.
ʑ
Foam escaping from the
detergent drawer. – Too much detergent used?
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour
into compartment
II (not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and
“wandering” during the
spin cycle. – Are the appliance feet fixed?
Secure the appliance feet a Installation instructions .
– Transportation safety devices removed?
Remove the transportation safety devices
a
Installation
instructions .
ʑ
Indicator lamps do not
function during
operation. – Power cut?
– Fuses triggered? Reset/change the fuses.
– If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence
longer than usual. – Not a fault - unbalanced load detection system adjusts
imbalance by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
ʑ
Detergent residues on
the laundry. – Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Select Ə ƒƗƘƖƠơƖ ( Rinse) or brush the laundry after washing.
If you cannot correct a fault yourself or a repair is required:
– Turn the programme selector to
stop and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service a Installation instructions.
WXP801B5