Pitney Bowes OfficeRight DF800 Operator'S Manual Download

Page: 10 / 56

1 • Introduction

1-4

SDC820A

Stacker

Tray Stacker

Your.OfficeRight™.Folder.DF800.Machine.comes.equipped.with.

a.Tray.Stacker..This.stacker.sits.on.the.table.and.collects.exiting.

material.

Conveyor Stacker CS88 - DF900 (optional extra for DF800)

Your.OfficeRight™.Folder.DF900.Machine.comes.equipped.with.

a.Conveyor.Stacker..A.Conveyor.Stacker.can.be.added.to.your.

DF800.as.an.optional.extra..This.stacker.allows.organised.collation.

of.material.on.exit.of.your.folding.machine..It.is.able.to.hold.larger.

quantities.of.exiting.material.and.is.recommended.for.all.frequently.

used.machines..Contact.your.sales.representative.for.further.

information.

Machine Configurations

The.following.machine.configurations.are.available:

•. DF800.(A4.Folding.Machine).with.Tray.Stacker.
•. DF900.(A3.Folding.Machine).with.Conveyor.Stacker.CS88.

Conveyor.Stacker.CS88.(Can.be.added.as.an.additional.

feature.to.the.DF800)

•. High.Capacity.Extension.(Can.be.added.as.an.additional.

feature.to.either.DF800.or.DF900.with.a.Conveyor.Stacker.

CS88.already.attached).
Cross-fold.Kit.(An.optional.extra.feature.on.the.DF900.Only).

IMPORTANT:

Model.and.features.availability.varies.by.country..

Contact.your.machine.supplier.for.more.information.
Inclusion.within.this.guide.does.not.guarantee.availability.of.a.

particular.model.or.feature.within.your.country.

•

High Capacity Extension (optional extra)

The.High.Capacity.Stacker.is.an.optional.extra.to.your.OfficeRight™.

Folder.DF800/DF900..The.High.Capacity.Stacker.is.an.extension.to.

the.Conveyor.Stacker.and.is.able.to.hold.larger.quantities.of.material.

which.results.in.the.stacker.needing.to.be.emptied.less.often..If.you.

run.regular.large.quantity.jobs,.the.High.Capacity.Extension.may.

be.a.beneficial.addition.to.your.OfficeRight™.Folder.DF800/DF900.

system..Contact.your.sales.representative.for.further.information.

Summary of Contents for OfficeRight DF800

























































Search results

Summary of Contents for OfficeRight DF800

Reviews:

Related manuals for OfficeRight DF800

Brands by name

Popular brands

Pitney Bowes OfficeRight DF800, Operator'S Manual

Search results

Summary of Contents for OfficeRight DF800

Reviews:

Related manuals for OfficeRight DF800

Brands by name

Popular brands