Pitney Bowes Connect+ 1000 Operator'S Manual Download

Page: 342 / 349

How to resolve tape feeding issues

This procedures describes some common tape feeding problems and how to correct them.

Issue 1

Tape stoppage is occurring

Cause(s)

Adhesive is left on the leading edge of the new tape roll.

The leading edge of the tape is rolled or folded under the tape roller.

Resolution

If necessary, remove the tape roll.

Clear the tape stoppage. For more information, refer to How to clear a tape stoppage.

Re-install the tape roll.

Issue 2

System is not wetting gummed tape.

Cause(s)

Tape moistener brush is dry due to air block in tubing.

Resolution

Remove the tape sealant bottle and re-install. Repeat as necessary until tape moistener brush becomes
wet.

Issue 3

Tape button is not available on the Run Mail screen.

Cause

You have selected a mode (such as WEIGH-ON-THE-WAY® (W-O-W®) mode) that requires mail be
fed though the mailing system.

Troubleshooting

Pitney Bowes

Operator Guide

February, 2018

Page 342 of 349

Summary of Contents for Connect+ 1000






























































































































































































































































































































































Search results

Summary of Contents for Connect+ 1000

Reviews:

Related manuals for Connect+ 1000

Brands by name

Popular brands

Pitney Bowes Connect+ 1000, Operator'S Manual

Search results

Summary of Contents for Connect+ 1000

Reviews:

Related manuals for Connect+ 1000

Brands by name

Popular brands