Piper Aircraft Corporation Malibu Mirage PA-46-350P Airplane Maintenance Manual Download

Page: 954 / 1956

PAGE 8
Feb 28/07

5D12

34-20-00

PIPER AIRCRAFT, INC.

PA-46-350P, MALIBU MIRAGE

MAINTENANCE MANUAL

CHART 5 (Sheet 1 of 3)

TROUBLESHOOTING EADI (i.e. - PFD)

Trouble

Cause

Remedy

No display visible at power up.

+28 VDC power missing.

Check wiring & bus voltage.

+28 VDC Return missing.

Check wiring.

Failed PFD.

Replace PFD.

EADI Display Down mode

Check EADI Display Down

selected.

switch.

Test mode visible at power up.

Stuck Baro pushbutton.

Check Baro pushbutton.

PFD failed self test.

Replace PFD.

Display brightness does not

28 VDC lighting bus not

Check wiring and 28 VDC

change when PFD brightness

connected or not functional.

lighting bus.

control operated.

Brightness control not functional.

Check Brightness control.

Failed PFD.

Replace PFD.

Barometric correction does not

PFD in test mode.

Ensure PFD in mission

change when BARO Rotary

operational mode.

control is rotated.

Failed PFD.

Replace PFD.

Barometric correction does not

PFD in test mode.

Ensure PFD in mission

change to standard setting when

operational mode.

Baro pushbutton is pressed.

Failed PFD.

Replace PFD.

Unable to enter test mode when

Airspeed equal to or greater

Ensure airspeed is less

Baro pushbutton is pressed.

than 40 knots detected.

than 40 knots.

Unit not powered off before

Ensure unit is powered off

Baro Pushbutton is pressed.

before Baro Pushbutton is
pressed.

Baro Pushbutton pressed and

Ensure Baro Pushbutton is

held for insufficient time.

pressed and held until
initialization page displays.

Failed PFD.

Replace PFD.

Test page does not change when

PFD in mission operational mode.

Ensure PFD in test mode.

Baro Rotary Control is rotated.

Failed PFD.

Replace PFD.

Power on self test status on

Failed PFD.

Replace PFD.

Configuration Data page is
indicated as FAIL.

Configuration discrete parity

Parity input (Configuration

Check configuration

status on Configuration Data

Discrete 7) not wired correctly.

discrete setting.

page is indicated as FAIL.

Check wiring.

Failed PFD.

Replace PFD.

Summary of Contents for Malibu Mirage PA-46-350P





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Malibu Mirage PA-46-350P

Reviews:

Related manuals for Malibu Mirage PA-46-350P

Brands by name

Popular brands

Piper Aircraft Corporation Malibu Mirage PA-46-350P, Airplane Maintenance Manual

Search results

Summary of Contents for Malibu Mirage PA-46-350P

Reviews:

Related manuals for Malibu Mirage PA-46-350P

Brands by name

Popular brands