background image

PAGE 1 

Feb 28/07

7F1

73-30-00

PIPER AIRCRAFT, INC.

PA-46-350P, MALIBU MIRAGE

MAINTENANCE MANUAL

INDICATING

NOTE:

Serial numbers 4636021 and up

incorporate Integrated Engine Instrumentation Systems. See

Section 77-40-00 for more information.

1.

Fuel Flow Gauge

The fuel flow gauge is mounted to the right of center in the upper section of the instrument panel, and is
electrically operated by the flow transducer.

A.

Troubleshooting

See Chart 1.

B.

Removal

(1)

Gain access to the instrument form behind the instrument panel. Disconnect the electrical
connection from the instrument.

(2)

Remove the post light(s) by turning off nut.

(3)

Remove the screws securing the instrument to th e panel.

(4)

Remove the instrument from the panel.

C.

Installation

(1)

Place the instrument in its proper panel cutout and secure with screws.

(2)

Install the post light(s) and secure. Do not overtighten the nut.

(3)

Connect the electrical connector to the gauge.

2.

Fuel Pressure Low Warning Light

Illumination of the FUEL PRESS annunciator light indicates impending fuel starvation due to insufficient
fuel pressure to the engine. See also 31-50-00 and 91-31-50.

3.

Fuel Pump

A.

Adjustment

To adjust the fuel pump output pressure:

(1)

Loosen the jamnut on the adjustment screw to allow free movement.

(2)

Adjust the pump pressure by turning screw in or out.

(3)

Tighten fuel pump jamnut and perform operation check.

Trouble

Cause

Remedy

Pointer oscillates.

Air in fuel line.

Purge line.

CHART 1

TROUBLESHOOTING FUEL FLOW GAUGE

Summary of Contents for Malibu Mirage PA-46-350P





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews: