Pioneer VSX-LX504 Instruction Manual Download

Page: 11 / 203

≫

≫

≫

≫

≫

≫

INPUT SELECTOR dial: Switch the input to be played.

FL OFF indicator: This lights when you have pressed DIMMER repeatedly to

turn the display off.

STATUS button: Switches the information on the display. (

p128

)

4. ZONE 2 ON/OFF button: Turns ZONE 2 ON/OFF. (

p116

)

ZONE 3 ON/OFF button: Turns ZONE 3 ON/OFF. (

p118

)

6. ZONE CONTROL button: Controls the multi-zone function. (

p115

)

7. DIMMER button: You can switch the display off or adjust the brightness of the

display in three steps.

Display (

p12

)

PERSONAL PRESET 1/2/3 buttons: Registers the current setting conditions

such as input selector, listening mode, etc. or call the registered settings.

(

p121

)

10.

NETWORK indicator: This lights when "NET" is selected with the input

selector and the unit is connected to the network. Lights up when any of the

following functions is working or enabled in standby state of this unit. When

this indicator is lighting, the power consumption in standby state increases,

however, the increase in power consumption is minimized by entering the

HYBRID STANDBY mode where only the essential circuits operate. It does not

light when ZONE 2/ZONE 3 is on, however.

–

HDMI CEC (

p159

)

–

HDMI Standby Through (

p159

)

–

USB Power Out at Standby (

p161

)

–

Network Standby (

p161

)

–

Bluetooth Wakeup (

p161

)

11.

Remote control sensor: Receives signals from the remote controller.

•

The signal range of the remote controller is within about 16´/5 m, at an

angle of 20° on the perpendicular axis and 30° to either side.

12.

MCACC indicator: This lights when you have enabled the speaker calibration

made with MCACC. (

p171, 183

)

13. MASTER VOLUME

14.

STANDBY/ON button: When the power is turned on, the periphery of the

button lights up. It also lights up when ZONE 2/ZONE 3 is turned on.

15. AV ADJUST button: Settings such as "HDMI" and "Audio" can be made quickly

during play on the TV screen. (

p179

)

16. HOME button: Displays the Home. (

p145, 170, 175

)

17.

Cursor buttons ( / / / )

and ENTER button: Select the item with the

cursors and press ENTER to confirm. Use them to tune to stations when using

TUNER. (

p110

)

18. RETURN button: Returns the display to the previous state.

19. TUNING MODE button: Switches the tuning mode. (

p110

)

20.

PHONES jack: Headphones with a standard plug (ø1/4"/6.3 mm) are

connected.

21. SETUP MIC jack: The supplied speaker setup microphone is connected.

(

p171, 183

)

22.

Listening mode button: Switches the listening mode. (

p126

)

23.

USB port: A USB storage device is connected so that music files stored in it

can be played. Supply of power to USB devices while in the standby mode is

not supported. (

p97

)

24.

AUX INPUT HDMI jack: Connect a video camera, etc. using an HDMI cable.

(

p77

)

25. Front flap

Summary of Contents for VSX-LX504












































































































































































































Search results

Summary of Contents for VSX-LX504

Reviews:

Related manuals for VSX-LX504

Brands by name

Popular brands

Pioneer VSX-LX504, Instruction Manual

Search results

Summary of Contents for VSX-LX504

Reviews:

Related manuals for VSX-LX504

Brands by name

Popular brands