Pioneer VSX-LX504 Instruction Manual Download

Page: 118 / 203

118

≫

≫

≫

≫

≫

≫

Playing Back (ZONE 3)

In the remote controller operation, while pressing and holding the ZONE 3 SHIFT

button on the remote controller, operate with each button. Settings are required to

playback a source in ZONE 3.

When outputting from the speakers:

Set "Speaker" - "Configuration" - "Zone

Speaker" in the System Setup menu (

p151

) to "Zone 2/Zone 3".

When outputting from the pre-main amplifier or the power amplifier:

Set

"Speaker" - "Configuration" in the System Setup (

p150

) to one of the

following.

–

Set "Speaker Channels" to "2.1 ch", "3.1 ch", "4.1 ch", or "5.1 ch"

–

Set "Speaker Channels" to "2.1.2 ch", "3.1.2 ch", "4.1.2 ch", or "5.1.2 ch",

and set "Bi-Amp" and "Zone Speaker" to "No"

Point the remote controller at the unit, and while pressing and holding the

ZONE 3 SHIFT button on the remote controller, press

• "Z3" on the display of the main unit lights up.

While pressing and holding the ZONE 3 SHIFT button on the remote controller,

press the input selector of the input source you want to play in the separate

room. When operating on the main unit, press the ZONE CONTROL button

repeatedly to select "Z3" on the display, then within 8 seconds select the input

you want to play in another room using the input selector dial.

If the unit is connected to the pre-main amplifier in the separate room, adjust

the volume on the pre-main amplifier. If the unit is connected to the power

amplifier or ZONE speaker in the separate room, adjust the volume with

the volume button while pressing and holding the ZONE 3 SHIFT button on

the remote controller. When operating on the main unit, press the ZONE

CONTROL button repeatedly to select "Z3" on the display, then within 8

seconds adjust using the MASTER VOLUME knob.

•

When connecting the power amplifier, set "Multi Zone" - "Zone 3" - "Output

Level" (

p167

) to "Variable" on the System Setup menu. If it is not set,

a large volume is output and the power amplifier, speakers, etc. may be

damaged.

Summary of Contents for VSX-LX504












































































































































































































Search results

Summary of Contents for VSX-LX504

Reviews:

Related manuals for VSX-LX504

Brands by name

Popular brands

Pioneer VSX-LX504, Instruction Manual

Search results

Summary of Contents for VSX-LX504

Reviews:

Related manuals for VSX-LX504

Brands by name

Popular brands