Pioneer VSX-LX503 Instruction Manual Download Page 127

Page: 127 / 174

127

≫

≫

≫

≫

≫

≫

Audio Adjust

Dual Mono / Mono

Change the settings of multiplex audio playback.

Setting Item

Default Value

Setting Details

Dual Mono

Main

Set the audio channel or language to be output

when playing multiplex audio or multilingual

broadcasts, etc.

"Main": Main channel only

"Sub": Sub channel only

"Main/Sub": Main and sub channels are output at

the same time.

• For multiplex audio broadcasts, pressing the

button on the remote controller will display "1+1"

on the main unit’s display.

Mono Input

Channel

Left + Right

Set the input channel to play 2-ch digital sources

such as Dolby Digital, or 2-ch analog/PCM sources

in the Mono listening mode.

"Left": Left channel only

"Right": Right channel only

"Left + Right": Left and right channels

Dolby

Change the setting of when Dolby signals are input.

Setting Item

Default Value

Setting Details

Loudness

Management

When playing Dolby TrueHD, enable the dialog

normalization function which keeps the volume of

dialog at a certain level. Note that when this setting

is Off, the DRC function that allows you to enjoy

surround at low volumes is fixed to off when playing

Dolby Digital Plus/Dolby TrueHD.

"On": When this function is used

"Off": When this function is not used

Volume

Change the Volume settings.

Setting Item

Default Value

Setting Details

Mute Level

-∞dB

Set the volume lowered from the listening volume

when muting is on. Select a value from "-∞dB",

"-40dB" and "-20dB".

Volume Limit

Off

Set the maximum value to prevent the volume

from becoming too loud. Select a value from "Off",

"-32 dB" to "+17 dB".

Power On Level

Last

Set the volume level of when the power is turned

on. Select a value from "Last" (Volume level before

entering standby mode), "-∞ dB", and "-81.5 dB" to

"+18.0 dB".

• You cannot set a higher value than that of

"Volume Limit".

Headphone Level 0.0 dB

Adjust the output level of headphones. Select a

value between "-12.0 dB" and "+12.0 dB".

Summary of Contents for VSX-LX503















































































































































































Search results

Summary of Contents for VSX-LX503

Reviews:

Related manuals for VSX-LX503

Brands by name

Popular brands

Pioneer VSX-LX503, Instruction Manual

Search results

Summary of Contents for VSX-LX503

Reviews:

Related manuals for VSX-LX503

Brands by name

Popular brands