Pioneer VSX-LX503 Instruction Manual Download Page 10

Page: 10 / 174

≫

≫

≫

≫

≫

≫

1. DIGITAL AUDIO IN OPTICAL/COAXIAL jacks: Input TV or AV component

digital audio signals with a digital optical cable or digital coaxial cable.

ANTENNA AM LOOP/FM UNBAL 75Ω terminal: The supplied antennas are

connected.

3. COMPONENT VIDEO IN jacks: Input the AV component video signals with a

component video cable. (Compatible only with 480i or 576i resolution.)

USB port: A USB storage device is connected so that music files stored in it

can be played. (

p83

) You can also supply power (5 V/500 mA) to USB

devices with a USB cable.

VIDEO IN jacks: Input the AV component video signals with an analog video

cable.

6. NETWORK port: Connect to the network with a LAN cable.

Wireless antenna: Used for Wi-Fi connection or when using a BLUETOOTH

enabled device. Adjust their angles according to the connection status.

8. RS-232C port: Connect a home control system equipped with an RS-232C

port. For adopting a home control system, contact the specialized stores.

9. HDMI OUT jacks: Transmit video signals and audio signals with an HDMI

cable connected to a monitor such as a TV or projector.

10. HDMI IN jacks: Transmit video signals and audio signals with a HDMI cable

connected to an AV component.

11. AC IN: The supplied power cord is connected.

12. SIGNAL GND terminal: The ground wire of the turntable is connected.

13. AUDIO IN jacks: Input AV component audio signal with an analog audio cable.

14. IR IN/OUT port: Connect a remote control receiver unit.(

p71

)

15.

12V TRIGGER OUT A/B jack: Connect a device equipped with a 12V trigger

input jack to enable power link operation between the device and this unit.

(

p72

)

16. SPEAKERS terminals: Connect speakers with speaker cables. (North

American models support banana plugs.)

17. PRE OUT jacks: Connect a power amplifier. (

p57

)

18. SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a

subwoofer cable. Up to two powered subwoofers can be connected. The same

signal is output from each of the SUBWOOFER PRE OUT jacks.

19. ZONE 3 PRE/LINE OUT jacks: Output audio signals with an analog audio

cable connected to a pre-main amplifier or a power amplifier in a separate

room (ZONE 3).

HEIGHT 2 PRE OUT jacks: Connect a power amplifier. (

p57

)

20. ZONE 2 PRE/LINE OUT jacks: Output audio signals with an analog audio

cable to a premain amplifier or a power amplifier in a separate room (ZONE 2).

Summary of Contents for VSX-LX503















































































































































































Search results

Summary of Contents for VSX-LX503

Reviews:

Related manuals for VSX-LX503

Brands by name

Popular brands

Pioneer VSX-LX503, Instruction Manual

Search results

Summary of Contents for VSX-LX503

Reviews:

Related manuals for VSX-LX503

Brands by name

Popular brands