<
ARB7050
>
24
SET
UP
SOUND
ED I T
SUPER
BASS
DSP
MODE
DOLBY
PROLOGIC
DIRECT
DOLBY
PROLOGIC
SUPER
BASS
L D
THEATER
DOLBY
PROLOGIC
SUPER
BASS
L D
A B
DISPLAY
D/A/CX
AUDIO
90
min
＋
1
2
3
4
5
1 0
6
7
8
9
0
VCR 1
THEATER
1
2
3
4
5
6
7
8
9
10
11
12
SYSTEM
OFF
SLEEP
V.
SEL
COPY
AC-3
SET
UP
SOUND
ED I T
SUPER
BASS
DSP
MODE
DOLBY
PROLOGIC
DIRECT
AC-3
OPERATING USING GUI
GUI
GUI (Graphic User Interface) lets you use the TV screen to
operate the system.
÷
Press the GUI MODE button on this unit or the GUI button on
the remote control and operation indications for the currently
selected function are displayed on the TV screen.
÷
To operate, use the
%
,
#
,
fi
,
@
buttons on the remote control
(they light up when the GUI mode is on) or the MULTI-JOG on
this unit to move the cursor (the hand shaped mark) displayed
on the TV screen. When the cursor is on the button you want
to operate, press the GUI ENTER button.
(Figure 1: Main Menu display)
1
AC-3:
Switches DOLBY SURROUND AC-3 on/off.
When on, “AC-3” is displayed on the right of the function
indications. (When the input selector is set to a source other
than LD or TV/SAT, it does not operate. Also, when TAPE 2 is on,
it does not operate.)
2
DOLBY PRO-LOGIC:
Switches DOLBY PRO-LOGIC on/off.
When on, “DOLBY PRO-LOGIC” is displayed to the right of the
function indications.
3
DSP MODE:
Switches between the five DSP modes as follows:
The selected mode is displayed to the right of the function
indications.
4
SUPER BASS:
Switches SUPER BASS on/off.
When on, “SUPER BASS” is displayed on the right of the
function indications.
5
DIRECT:
Press this to listen to source sound without passing the audio
signal through sound quality and balance adjusting circuitry.
The surround mode, rear and center speakers are automatically
switched off.
6
SOUND EDIT:
Press to make adjustments such as level setting for the currently
selected DSP mode, DOLBY SURROUND AC-3 or DOLBY PRO-
LOGIC.
When you press this button, the display changes to SOUND
EDIT indications. (Refer to page 30.)
7
SET UP:
Press this button and the display changes to the SET UP MENU.
(Refer to pages 31
–
33.)
8
Display change button:
Switches between Main Menu display (Figure 1) and Sub Menu
display (Figure 2).
9
COPY:
Press to copy from a LaserDisc to a VCR, or to copy between VCR
1 and VCR 2.
When you press this button, the display changes to COPY
indications. (This button is displayed only when the function is
LD, VCR 1 or VCR 2. Refer to page 28.)
0
V.SEL (VIDEO SIGNAL SELECTOR):
This switches only the video signal in sequence, leaving the
sound unchanged. (Refer to page 28.)
-
SLEEP:
This operates the sleep timer. Move the cursor to this button,
and each time you press the GUI ENTER button, timer settings
change as follows:
=
SYSTEM OFF:
Switches power to this unit, the TV and the currently selected
function off.
NOTE:
When you press the SYSTEM OFF button, power to components
not made by Pioneer switches on if power to these components
was already switched off.
÷
When the operating instructions say “Press the button”, this
means move the cursor to the desired button and press the
GUI ENTER button.
NOTE:
÷
If you do not perform any of the operations above within 10 ~ 30
seconds, the GUI display is canceled.
÷
<Multi-voltage model only>
Set the rear panel PAL/NTSC switch to match your TV’s color
system. The screen will be unclear if the color system does not
match.
RECEIVER CONTROL BUTTONS
÷
The buttons in the following explanation are the receiver operation button indications common to all function displays. (The illustration
shows LD operation indications.)
(Figure 2: Sub Menu display)
JAZZ
3
DANCE
HALL
SIM.SURR
(SIMULATED SURROUND)
2
2
3
3
THEATER
off
2
VCR 1
3
VCR 2
VIDEO
TV/SAT
LD
off
3
3
3
3
2
90 min
3
60 min
30 min
0 min (off)
2
3
3
