VSX-C402-S
112
1
2
3
4
1
2
3
4
C
D
F
A
B
E
7
SCART AV connectors
The four SCART-type AV connectors carry video and
analog audio.
VIDEO IN/OUT AV connector
AV connector for the
VIDEO
input. When the receiver
is set to any other input, that signal is output from the
VIDEO IN/OUT
AV connector.
DVR/TV IN/OUT AV connector
AV connector for the
DVR/TV
input. When the
receiver is set to any other input, that signal is output
from the
DVR/TV IN/OUT
AV connector.
DVD IN AV connector
AV connector for the
DVD
input.
STB IN AV connector
AV connector for the
STB
input.
The table below shows the input and output video
formats available for each AV connector.
• All AV connectors also have audio in. The
VIDEO
and
DVR/TV
connectors also have audio out.
• The
VIDEO
and
DVR/TV
connectors are compatible
with i/o -Link.A, T-V Link, Easy Link, MegaLogic,
SMARTLINK, Q-Link, DATALOGIC, NextTView Link, etc.
8
SURROUND PREOUT
For XW-HTD525 wireless speaker system only:
The
SURROUND PREOUT
terminal is intended for use
with a wireless system. See your wireless speaker
manual for more details on connecting up.
The AV Direct mode
The AV Direct mode allows the receiver to pass audio/
video signals arriving at one of the AV connector inputs
to the AV connector outputs without the sound being
output through the speakers connected to the receiver.
This allows you to operate your other components as if
they were connected directly to each other without the
receiver being on. One use for this is if you want to record
from your satellite receiver to your VCR (both connected
to this receiver) without the receiver being switched on.
You could also use the AV Direct mode to watch a video,
using your TV’s speakers for the audio, without switching
on the receiver.
You can switch into AV Direct mode (from either standby
or on) using the
AV DIRECT
button on the remote
control. However, it’s also possible to set the receiver to
switch the AV Direct function on automatically when an
incoming signal is detected. See also
AV Direct setting on.
The diagram below shows how the
AV DIRECT
and the
STANDBY/ON
buttons switch the receiver between
standby, AV Direct mode, and on.
Installing the receiver
• When installing this unit, make sure to put it on a
secure and level plane that is stable.
• Don’t place it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that gives
off a magnetic field). This may interfere with the
sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is a vibration or other
movement
– in places that are very dusty
– in places that have hot fumes or oils (such as a
kitchen)
When making cable connections
Be careful not to arrange cables in a manner that bends
the cables over the top of this unit. If the cables are laid
on top of the unit, the magnetic field produced by the
transformers in this unit may cause a humming noise to
come from the speakers.
Connector
Input
Output
DVD
Composite, S-video,
RGB
–
STB
Composite, S-video,
RGB
–
VIDEO
Composite, S-video,
RGB
Composite
DVR/TV
Composite
Composite, S-video,
RGB
Standby
AV Direct
On
RECEIVER
AV DIRECT
Standby
AV Direct
On
Summary of Contents for VSX-C402-K
