Pioneer VSX-934 Instruction Manual Download Page 71

Page: 71 / 153

≫

≫

≫

≫

≫

≫

When FM broadcasts reception is poor:

Perform the procedure for "Tuning

Manually" (

p71

). Note that if you tune manually, the reception for FM

broadcasts will be monaural rather than stereo, irrespective of the sensitivity of

the reception.

Tuning Manually

Note that if you tune manually, the reception for FM broadcasts will be monaural

rather than stereo, irrespective of the sensitivity of the reception.

1. Press TUNER repeatedly to select either "AM" or "FM".

2. Press MODE repeatedly to display "TunMode: Manual" on the display.

3. While pressing the cursors / , select the desired radio station.

• Each time you press the cursors / , the frequency changes by 1 step.

If the button is held down, the frequency changes continuously, and if the

button is released, the frequency stops changing.

Frequency step setting

Press

on the remote controller, and from Home displayed select "System

Setup" - "Miscellaneous" - "Tuner" - "AM/FM Frequency Step" or "AM Frequency

Step", and then select the frequency step for your area. Note that when this

setting is changed, all radio presets are deleted.

❏

Presetting a Radio Station (

p72

)

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands