Pioneer VSX-934 Instruction Manual Download Page 43

Page: 43 / 153

≫

≫

≫

≫

≫

≫

Connecting an AV Component in a Separate Room (Multi-zone Connection)

Connecting a TV (ZONE 2)

While a disc is played on a Blu-ray Disc player in the main room (where this unit

is located), you can play the video and audio of the same Blu-ray Disc player or

another AV component on the TV equipped with an HDMI IN jack in a separate

room (ZONE 2). The TV in the separate room can play only the video of devices

connected to the HDMI IN1 to IN3 jacks of this unit.

•

The audio from externally connected AV components can be output only when

the signal is 2ch PCM audio. It may also be necessary to convert the audio

output of the AV component to PCM output.

•

When video and audio via HDMI input are output to ZONE 2, set "Input/Output

Assign" - "TV Out / OSD" - "Zone 2 HDMI"

(

p103

) to "Use" on the System

Setup menu.

HDMI cable

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands