Pioneer VSX-934 Instruction Manual Download Page 40

Page: 40 / 153

≫

≫

≫

≫

≫

≫

To Non-ARC TV

If the TV does not support the ARC (Audio Return Channel) function (*), connect

an HDMI cable and digital optical cable.

• If you use a cable set-top box, etc. connected to the input jack of this unit to

watch TV (without using a TV’s built-in tuner), connection with a digital optical

cable or analog audio cable is not required.

•

Another TV or projector can be connected to the HDMI OUT SUB jack. Switch

between MAIN and SUB using the HDMI MAIN/SUB button (

p16

) on the

remote controller or "AV Adjust" (

p129

). Note that this jack is not ARC-

compatible.

•

If devices with different resolutions are connected to HDMI OUT MAIN jack

and SUB jack, images are output with the lower resolution.

(*) ARC function: This function transmits the audio signals of the TV via an

HDMI cable, and plays the audio of the TV on this unit. Connection to an ARC-

compatible TV is complete with one HDMI cable. To check if the TV supports the

ARC function, refer to the instruction manual of the TV, etc.

HDMI cable,

Digital optical cable

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands