Pioneer VSX-934 Instruction Manual Download Page 15

Page: 15 / 153

≫

≫

≫

≫

≫

≫

1. DIGITAL AUDIO IN OPTICAL/COAXIAL jacks: Input TV or AV component

digital audio signals with a digital optical cable or digital coaxial cable.

ANTENNA AM LOOP/FM UNBAL 75 Ω terminal: The supplied antennas are

connected.

Wireless antenna: Used for Wi-Fi connection or when using a BLUETOOTH

enabled device. Adjust their angles according to the connection status.

USB port: A USB storage device is connected so that music files stored in it

can be played. (

p57

) You can also supply power (5 V/500 mA) to USB

devices with a USB cable.

5. NETWORK port: Connect to the network with a LAN cable.

6. HDMI OUT jacks: Transmit video signals and audio signals with a HDMI cable

connected to a TV.

7. HDMI IN jacks: Transmit video signals and audio signals with a HDMI cable

connected to an AV component.

8. Power cord

SIGNAL GND terminal: The ground wire of the turntable is connected.

10.

AUDIO IN jacks: Input AV component audio signal with an analog audio cable.

11.

SPEAKERS terminals: Connect speakers with speaker cables. (North

American models support banana plugs. Use a plug 4 mm in diameter. Y plug

connection is not supported.)

12.

ZONE B LINE OUT jacks: Connect to a pre-main amplifier with an analog

audio cable, and simultaneously output audio of the same source as that of

the speakers (ZONE A) connected to this unit.

13.

SUBWOOFER PRE OUT jack: Connect a powered subwoofer with a

subwoofer cable. Up to two powered subwoofers can be connected. The same

signal is output from each of the SUBWOOFER PRE OUT jacks.

Summary of Contents for VSX-934


























































































































































Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands

Pioneer VSX-934, Instruction Manual

Search results

Summary of Contents for VSX-934

Reviews:

Related manuals for VSX-934

Brands by name

Popular brands