Pioneer VSX-933 Instruction Manual Download Page 97

Page: 97 / 131

≫

≫

≫

≫

≫

≫

Manual MCACC

EQ Adjust

If you perform Full Auto MCACC then settings are automatic, but you can also

adjust the output volume of the range of each connected speaker to suit your own

preferences. You can adjust the volume of the different sound ranges for each

of the speakers. You can set three different equalizers in Preset 1 to 3. You can

select up to 4 bands for the Subwoofer and 9 bands for all other speakers.

Setting Item

Default Value

Setting Details

Front Left

0 dB

After selecting the speaker frequency from between

"63 Hz" and "16 kHz" with the cursors

, adjust

the volume of that frequency between "-12.0 dB"

and "+12.0 dB" with

/ .

•

"63 Hz" can only be selected when this speaker

is set to "Large" in "System Setup" - "Speaker" -

"Crossover".

Center

0 dB

After selecting the speaker frequency from between

"63 Hz" and "16 kHz" with the cursors

, adjust

the volume of that frequency between "-12.0 dB"

and "+12.0 dB" with

/ .

•

"63 Hz" can only be selected when this speaker

is set to "Large" in "System Setup" - "Speaker" -

"Crossover".

• If an item cannot be selected even though

connection is correct, check that the settings in

"System Setup" - "Speaker" - "Configuration"

- "Speaker Channels" matches the number of

connected channels.

Front Right

0 dB

After selecting the speaker frequency from between

"63 Hz" and "16 kHz" with the cursors

, adjust

the volume of that frequency between "-12.0 dB"

and "+12.0 dB" with

/ .

•

"63 Hz" can only be selected when this speaker

is set to "Large" in "System Setup" - "Speaker" -

"Crossover".

Setting Item

Default Value

Setting Details

Height Left

0 dB

After selecting the speaker frequency from between

"63 Hz" and "16 kHz" with the cursors

, adjust

the volume of that frequency between "-12.0 dB"

and "+12.0 dB" with

/ .

•

"63 Hz" can only be selected when this speaker

is set to "Large" in "System Setup" - "Speaker" -

"Crossover".

•

The setting cannot be changed if "Zone 2" is set

in "Configuration" - "Zone Speaker" and Zone 2

is on.

• If an item cannot be selected even though

connection is correct, check that the settings in

"System Setup" - "Speaker" - "Configuration"

- "Speaker Channels" matches the number of

connected channels.

Height Right

0 dB

After selecting the speaker frequency from between

"63 Hz" and "16 kHz" with the cursors

, adjust

the volume of that frequency between "-12.0 dB"

and "+12.0 dB" with

/ .

•

"63 Hz" can only be selected when this speaker

is set to "Large" in "System Setup" - "Speaker" -

"Crossover".

•

The setting cannot be changed if "Zone 2" is set

in "Configuration" - "Zone Speaker" and Zone 2

is on.

• If an item cannot be selected even though

connection is correct, check that the settings in

"System Setup" - "Speaker" - "Configuration"

- "Speaker Channels" matches the number of

connected channels.

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands