Pioneer VSX-1120-K, Operating Instructions Manual

Page: 34 / 108

Connecting your equipment 03
34
En
Operating other Pioneer components
with this unit’s sensor
Many Pionee r com p onents have
SR CONTROL
jacks
which can be used to link com p onents togethe r so that
you can use just the r emote senso r of one com p onent.
When you use a r emote cont r ol, the cont r ol signal is
p assed along the chain to the a ppr o pr iate com p onent.
1
Important
• Note that if you use this featu r e,
make sure that you
also have at least one set of analog audio, video or
HDMI jacks connected
to anothe r com p onent fo r
g r ounding p u rp oses.
1 Decide which component you want to use the
remote sensor of.
When you want to cont r ol any com p onent in the chain,
this is the r emote senso r at which you’ll p oint the
co rr es p onding r emote cont r ol.
2 Connect the CONTROL OUT jack of that component
to the CONTROL IN jack of another Pioneer component.
Use a cable with a mono mini- p lug on each end fo r the
connection.
Continue the chain in the same way fo r as many
com p onents as you have.
Plugging in the receiver
Only p lug in afte r you have connected all you r
com p onents to this r eceive r , including the s p eake r s.
1 Plug the supplied power cord into the AC IN socket
on the back of the receiver.
2 Plug the other end into a power outlet.
2
CAUTION
• Handle the p owe r co r d by the p lug p a r t. Do not p ull
out the p lug by tugging the co r d, and neve r touch the
p owe r co r d when you r hands a r e wet, as this could
cause a sho r t ci r cuit o r elect r ic shock. Do not p lace
the unit, a p iece of fu r nitu r e, o r othe r object on the
p owe r co r d o r p inch the co r d in any othe r way. Neve r
make a knot in the co r d o r tie it with othe r cables. The
p owe r co r ds should be r outed so that they a r e not
likely to be ste pp ed on. A damaged p owe r co r d can
cause a fi r e o r give you an elect r ic shock. Check the
p owe r co r d once in a while. If you find it damaged,
ask you r nea r est Pionee r autho r ized inde p endent
se r vice com p any fo r a r e p lacement.
• Do not use any p owe r co r d othe r than the one
su pp lied with this unit.
• Do not use the su pp lied p owe r co r d fo r any p u rp ose
othe r than that desc r ibed below.
• The r eceive r should be disconnected by r emoving the
mains p lug f r om the wall socket when not in r egula r
use, e.g., when on vacation.
• Make su r e the blue  STANDBY/ON light has gone
out befo r e un p lugging.
• If you have connected s p eake r s with a 6
Ω
im p edance, change the im p edance setting befo r e
tu r ning on the p owe r .
Note
1 • If you want to cont r ol all you r com p onents using this r eceive r ’s r emote cont r ol, see
Setting the remote to control other components
on
p age 62.
• If you have connected a r emote cont r ol to the
CONTROL IN
jack (using a mini- p lug cable), you won’t be able to cont r ol this unit using the
r emote senso r .
RS-232C
SPEAKERS
MONITOR
OUT
P
R
Y
ANTENNA
FM UNBAL 75 AM LOOP
OUT
IN IN
P
B
A
CONTROL
EXTENSION
IR
IN
IN
OUT
OUT
(OUTPUT
5 V
150 mA
MAX)
Class 2 Wiring
CONTROL
IN OUT
IN OUT
CONTROL
2 Afte r this r eceive r is connected to an AC outlet, a 2 second to 10 second HDMI initialization pr ocess begins. You cannot ca rr y out any
o p e r ations du r ing this pr ocess. The
HDMI
indicato r in the f r ont p anel dis p lay blinks du r ing this pr ocess, and you can tu r n on this r eceive r
once it has sto pp ed blinking. When you set the Control with HDMI to OFF , you can ski p this pr ocess. Fo r details about the Control with HDMI
featu r e, see
Control with HDMI function
on p age 52.
VSX-1120_UXJCB.book 34 ページ ２０１０年３月１０日 水曜日 午後２時２分