background image

Fig. 2

Gray/black

White/black

Green

Violet

+

+

+

Power amp
(sold separately)

+

+

+

+

+

+

+

Power amp
(sold separately)

Power amp
(sold separately)

Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal (max.
300 mA 12 V DC).

System remote control

Left

Right

Rear speaker

Rear speaker

Fuse resistor

Yellow
To terminal always supplied with
power regardless of ignition switch
position.

Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.

Black (ground)
To vehicle (metal) body.

Orange/white
To lighting switch terminal.

Fuse resistor

White

Gray

Green/black

Violet/black

Rear speaker

Rear speaker

This Product

Antenna jack

Subwoofer

Front speaker

Connecting cords with RCA pin
plugs (sold separately)

IP-BUS cable

IP-BUS input (Blue)

Multi-CD player
(sold separately)

Subwoofer

Front speaker

Fuse holder

Front speaker

Front speaker

Yellow/black
If you use a cellular telephone,
connect it via the Audio Mute lead on
the cellular telephone. If not, keep the
Audio Mute lead free of any
connections.

Perform these connections when using a
different amp (sold separately).

TEL terminal

15 cm

15 cm

Front output (FRONT OUTPUT)

Rear output (REAR OUTPUT)

Subwoofer output
(SUBWOOFER OUTPUT)

Refer to handsfree telephone
unit’s manual (sold separately).

MIC terminal

With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.

15 cm

15 cm

Note:
• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-
ational vehicle, truck, or bus, check the battery
voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the 

battery cable before beginning

installation.

• Refer to the owner’s manual for details on con-

necting the power amp and other units, then make
connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake,
and seat rails. Do not route wiring in places that
get hot, such as near the heater outlet. If the insula-
tion of the wiring melts or gets torn, there is a dan-
ger of the wiring short-circuiting to the vehicle
body.

• Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or
the left and right 

speaker leads are common.

• If the RCA pin jack on the unit will not be used, do

not remove the caps attached to the end of the con-
nector.

• Speakers connected to this unit must be high-

power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke, or becoming damaged.

• When this product’s source is switched ON, a con-

trol signal is output through the blue/white lead.
Connect to an external power amp’s system remote
control or the car’s Auto-antenna relay control ter-
minal (max. 300 mA 12 V DC). If the car features
a glass antenna, connect to the antenna booster
power supply terminal.

• When an external power amp is being used with

this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do not
connect the blue/white lead to the power terminal
of the auto-antenna. Such connection could cause
excessive current drain and malfunction.

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a possi-
bility of short-circuiting if the leads are not insulat-
ed.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same colors
correctly.

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connected
to a terminal coupled with ignition switch ON/OFF
operations. If this is not done, the vehicle battery
may be drained when you are away from the vehi-
cle for several hours. (Fig. 1)

Fig. 1

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.

No ACC position

ACC position

ON

S

T

A

R

T

O

FF

ACC

ON

S

T

A

R

T

O

FF

DEH-P930

Printed in Japan

Imprimé au Japon

<CRD3446-A> UC

Connecting the Units

<ENGLISH>

This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.

• Cords for this product and those for other prod-

ucts may be different colors even if they have the
same function. When connecting this product to
another product, refer to the supplied Installation
manuals of both products and connect cords that
have the same function.

INST

ALLA

TION MANUAL

MANUEL D’INST

ALLA

TION

<KMMUF/01C00000>

Summary of Contents for Super Tuner III DEH-P930







Reviews: