background image

2

www.pioneerelectronics.com

CABINET MAINTENANCE

Use a cloth to wipe away dust and dirt.

If the enclosure is very dirty, wipe with a soft cloth
dipped in a neutral detergent diluted five to six
times with water, then wipe again with the dry
cloth.

Do not use thinner, benzene, cleaning sprays or
other chemical products on or near the enclosures
as the surfaces could be adversely affected.

NOTES:

Pioneer will not be responsible for any acci-

dents or damages resulting from improper in-
stallation.

USING THE ACCESSORIES

Confirm that the following accesories are in the
box when you open it:

< right >

< wrong >

10 —12 mm

1

Strip the insulation at the tip of the 

wire and twist the strands.

2

Turn the thumbscrew anti-

clockwise, make sure that the 
speaker wires are inserted well 
into the hole and turn the 
thumbscrew clockwise to fasten 
into position.

If you insert the speaker wire too far so that the insulation is touching the 
speaker terminal, you may not get any sound.

Connect the common-side 

speaker wire to the

           

terminal.

Connect the hot-side speaker 

wire to the      terminal.

REMARKS:

• Check that the wires are securely connected to

the terminals. A loose connection may cause not
just intermittent or distorted sound but short-cir-
cuiting and breakdown of the amplifier.

• If there is too much exposed wire outside the

terminal, speaker wires may touch causing the
amplifier to short, damaging the amplifier and
making it unusable.

• If the wires of one of the speakers have been

connected with the wrong polarities, you will find
when listening to a stereo recording that bass
sounds are weakened and the stereo effect nor-
mally obtained between the two speakers does
not exist.

CONNECTIONS

Switch off the amplifier power supply (OFF).

Connect the speaker wires to the input terminals at
the rear of the speaker; connect the common-side
wire to the 

·

 terminal and the hot-side wire to the

ª

 terminal. Bear in mind that the red input termi-

nal has a “

ª

“ polarity, and the black terminal has

a “

·

” polarity.

Connect the wire to the loudspeaker outlet termi-
nals of the amplifier. Connect the hot-side wire to
the 

ª

 terminal and the common-side wire to the

·

 terminal.

CAUTION:

The speakers are equipped with a protection
device to protect the transducers from extreme
conditions. Under these conditions the protec-
tion device will activate and stop the speaker
from producing sound. If this happens shut off
the system for 5-10 minutes and allow the pro-
tection device to reset.

● 

Speaker stands  + 1 polybag including 6 screws

Center speaker: 

This speaker stand 1 will enable you to set the centre 
speaker horizontally on a flat surface. The 2 screws that hold 
the speaker stand must be fixed into the dedicated insert in 
the speaker system.

Rear Speaker:
Before screwing the speaker stand 2 to the 

back of the cabinet, thread the speaker 
wires through the opening in the speaker 
stand and then connect them to the input 
terminal. The 2 screws that hold the 
speaker stand must be screwed into the 
dedicated inserts in the speaker.

This Mounting panel 3 will enable you to set 

the speaker system on your interior’s walls. 
Before screwing the mounting panel, make 
sure that wires are properly connected to the 
input terminal. The 2 screws that hold the 
mounting panel must be fixed into the 
dedicated inserts in the speaker system.

● 

3 Mounting panels

● 

1 Operating instruction/Warranty

1

2

3

Caution

In order to prevent the speaker from falling
make sure the wall is sturdy enough to sup-
port the weight of the speaker. Do not mount
it on plywood boards or soft-surface walls.
Mount the speaker system on a flat wall, this
will reduce the pressure on the screws, avoid-
ing the risk of become loose, and preventing
the speaker system from falling. If you are
unsure of the quality and strength of the wall,
consults a professional for advice.

Summary of Contents for S-LF3-CR

Page 1: ...n will be increased and you may damage the tweeter Avoid touching the diaphragms and suspen sions of the speaker units as they are fragile INSTALLATION PRECAUTIONS The S LF3 CR system is composed of 1 center speaker and 2 rear speakers For optimum effect install the rear speakers above ear level Install the centre speaker above or below the TV so that the sound of the center channel is local ized ...

Page 2: ...t the common side wire to the terminal and the hot side wire to the ª terminal Bear in mind that the red input termi nal has a ª polarity and the black terminal has a polarity Connect the wire to the loudspeaker outlet termi nals of the amplifier Connect the hot side wire to the ª terminal and the common side wire to the terminal CAUTION The speakers are equipped with a protection device to protec...

Page 3: ...it at a safe level One that lets the sound come through loud and clear without annoying blaring or distortion and most importantly without affecting your sensitive hearing Sound can be deceiving Over time your hearing comfort level adapts to higher volumes of sound So what sounds normal can actually be loud and harmful to your hearing Guard against this by setting your equipment at a safe level BE...

Page 4: ...r damage caused by the use of unauthorized parts or labor or from improper maintenance ALTERED DEFACED OR REMOVED SERIAL NUMBERS VOID THIS WARRANTY YOUR RIGHTS PUSA and POC excludes any obligation on its part for incidental or consequential damages related to the failure of products to function properly under the conditions set forth above IN THE U S A PUSA LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED...

Reviews: