1
2
3
7
AUTO
COOL
DRY
HEAT
FAN
AUTO
LOW
MED
HIGH
9
8
ON / OFF (Power) Button
Pressing this button once turns the power
to the system ON and OFF.
MODE (operation mode) Button
Pressing this button will switch its operating
modes in the following sequence of modes
Note: Cooling only versions of any system
will not respond to selection of HEAT mode.
FAN SPEED (selector) Button
Pressing this button will switch the speed of
the indoor unit’s fan (air flow volume) in the
following sequence
Note: Fan speed can not be controlled by the
remote while running AUTO or DRY modes.
TURBO (Performance) Button
Pressing this button activates the high
performance function so that the system
can establish the the desired temperature
level within the shortest amount of time, in
both COOL and HEAT modes.
(if the air conditioner is not equipped with
this function it will not respond)
UP Temperature Button ( )
Pressing this button each time will increase
the set temperature in 1F increments up to
a maximum of 86F
DOWN Temperature Button ( )
Pressing this button each time will decrease
the set temperature in 1F increments down to
a minimum of 62F
Notes:
Temperature controls are not available
while running FAN mode.
Press and hold UP and DOWN buttons
simultaneously to change the display
temperature between C and F degrees.
SILENCE (Quiet Mode) and
FP (Low Heat) Dual Function Button
Pressing this button briefly will set the compressor
and the indoor fan motor to run at their lowest
allowed speed settings for extra quiet operation.
However, when running this mode, the cooling
and heating capacity may not be satisfactory
if the zone heating or cooling loads are higher
than this low capacity system operates at.
Pressing and holding this button for 2 seconds will
activate LOW-HEAT (or Vacation) Mode, useful
when the room will be unattended during winter
to prevent frost. This mode can only be activated
when system is in HEAT mode. LOW-HEAT mode
will set the temperature down to 46F and run low
heat cycle to save energy. Deactivate by pressing
POWER, FAN, FP, TEMP or MODE buttons.
TIMER ON Button
Pressing this button each time will advance the
setting time for automatically starting the
system by 30 min each press up to reaching
10.0 and 60 min each press thereafter.
When the total set time elapses the
system will start automatically.
To cancel the ON set time, keep pressing the
TIMER ON button until display shows 0.0
MODE
MODE
FAN
TEMP
SLEEP
ON/OFF
SILENCE
FP
TIMER
ON
TIMER
OFF
1
2
4
3
8
9
7
5
6
10
12
11
13
14
SWING DIRECT
FOLLOW
ME
LED
SELF
CLEAN
TURBO
Operational Buttons
4
5
6
SELF CLEAN Button
Pressing this button will activate a fan only
mode to dry the internal components before
long term stoppage. This mode can only be
activated under COOL or DRY modes and
lasts 16 minutes before system turns off.
SLEEP Button
Activates Sleep mode, according to the human
natural sleep cycle, by lowering or increasing
the set temperature in 2 steps. When activated,
this mode changes the set temperature by 2F
for each for each of the first and second hours
of the sleep cycle and turns the system off when
a total period of 8 hours elapses. Available in
COOL, HEAT and AUTO Modes. Press any of
MODE, FAN or POWER button to cancel.
Note on DUAL FUNCTION Buttons:
TURBO/SELF-CLEAN, SWING-DIRECT and
LED-FOLLOW-ME buttons are dual function
buttons. LEFT and RIGHT edges of these
buttons activate the different specific function
printed nearest to that edge.
SILENCE/FP button is also a dual function
button that works activates different functions
based on the length of time pressed, which is
further explained.
MODE
MODE
FAN
TEMP
SLEEP
ON/OFF
SILENCE
FP
TIMER
ON
TIMER
OFF
1
2
4
3
8
9
7
5
6
10
12
11
13
14
SWING DIRECT
FOLLOW
ME
LED
SELF
CLEAN
TURBO
Operational Buttons
SLEEP Mode Details:
Human body temperature drops during sleep.
To match with this change in body temperature:
If the sleep mode is activated while running
COOL mode, the system will increase the set
temperature by 2F within 60 minutes and by
an additional 2F within the next 60 minutes.
If the sleep mode is activated while running
HEAT mode, the system will reduce the set
temperature by 2F within 60 minutes and by
an additional 2F within the next 60 minutes.
System turns off 8 hours after sleep mode is
activated. Use the Timer ON Function to start
the system automatically after sleep mode.
