background image

IMIM 

TT 

三竺己

G三

Timer operation 

Press the TIMER ON button can set the auto-on 

time of the unit.  Press the TIMER OFF  button 

can set the auto-off time of the unit. 

To set the Auto-on time. 

1. Press the TIMER ON button. The remote

controller shows TIMER ON, the last Auto-on

setting time and the signal "H" will be shown on

the LCD display area. Now it is ready to reset

the Auto-on time to START the operation.

2. Push the TIMER ON button again to set desired

Auto-on time. Each time you press the button,

the time increases by half an hour between 0

and 10 hours and by one hour between 10 and

24 hours.

3. After setting the TIMER ON ,there will be a one

second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "h" will disappear and the set temperature

will re-appear on the LCD display window.

To set the Auto-off time.
1. Press the TIMER OFF  button. The remote

controller shows TIMER OFF, the last Auto-off

setting time and the signal "H" will be shown on

the LCD display area. Now it is ready to reset

the Auto-off time to stop the operation.

2. Push the TIMER OFF  button again to set

desired Auto-off time. Each time you press the

button, the time increases by half an hour

between O and 10 hours and by one hour

between 10 and 24 hours.

3. After setting the TIMER OFF  ,there will be a

one second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "H " will disappear and the set temperature

will re-appear on the LCD display window.

IAcAur10N  I 

• The effective operation time set by the remote controller for the timer function

is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0,

5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20,

21, 22, 23 and 24.

[ Example of timer setting 

TIMER ON 

(Auto-on Operation) 

The TIMER ON feature is useful when you want 

the unit to turn on automatically before you return 

home. The air conditioner will automatically start 

operating at the set time. 

OoN 

,. ,.. 

CI.LIH

Start 

ff

Set 

6 hours later 

Example: 

To start the air conditioner in 6 hours. 

1. Press the TIMER ON button, the last setting

of starting operation time and the signal "H"

will show on the display area.

2. Press the TIMER ON button to display  "6.0H "

on the TIMER ON display of the remote

controller.

3. Wait for 3 seconds and the digital display

area will show the temperature again. The

"TIMER ON" indicator remains on and this

function is activated.

丿

Summary of Contents for RG52F3JBGEFU1









Reviews: