Pioneer GEX-P5750TVP, Installation Manual, Page: 4 / 7

6 . Blue
11. This unit
9 . To video output
3 m
6 . Blue
1. AV-B U S cable (supplied)
1. AV-B U S cable (supplied)
AV receiver
(e.g. AVH-
P575 0DVD)
(sold separately)
2.
6 . Blue
4. Black
3. Y ellow
1 6 . White / Red
3 m
3 m
AV-B U S cable
(supplied)
1.
3. Y ellow
3. Y ellow
3. Y ellow
4. Black
4. Black
4. Black
4. Black
6 . Blue
IP -B U S cable
(supplied)
8 .
10. RCA cable
(sold
separately)
Display
(e.g. AVD-W
8 000)
(sold separately)
12.
13. IP -B U S cable
(sold separately)
To video
1 input 14.
To video 2
input 1 5 .
1 6 . White / Red
10. RCA cable
(sold separately)
(
RCA cable
supplied with
DVD player)
1 7 .
DVD P layer
(e.g. X DV- P9
—
)
(sold separately)
1 8 .
M ulti-CD P layer
(sold separately)
1 9 .
3. Y ellow
4. Black
4. Black
20. U se AV-B U S cable ( 5 0 cm ) if necessary.
Vehicle Dynamics P rocessor
(e.g. AV G -VD P 1)
(sold separately)
5 .
5 0 cm
2 6 -pin cable
(supplied with Vehicle Dynamics P rocessor)
7 .
1. Blue
8 . This unit
1. Blue
3 m
6 . Black
IP -B U S cable
(supplied)
9 .
7 . IP -B U S input
3. P ioneer head unit
(sold separately)
AV-B U S cable
(supplied)
5 .
3 m
6 . Black
2. AV-B U S input
4. AV system display
(e.g. AV X - P765 0)
(sold separately)
10. This unit
5 . To video input
1. To video 1 input
7 . To rear out
(R E AR OU T)
9 . To front out
( F R ON T V I D EO OU T)
3 m
8 . Black
4. RCA cable
(sold separately)
6 . Y ellow
Display unit with RCA input j ack
(sold separately)
11.
3. Remote sensor
(supplied)
2. Display
(e.g. AVD-W 8 000)
(sold separately)
Fig. 16
«∂ qJA«
Fig. 13
±≥ qJA«
Fig. 14
±¥ qJA«
Fig. 15
±µ qJA«
1. This unit
2. F use holder
3. Y ellow
To terminal always supplied with power
regardless of ignition switch position.
6 . Black (ground)
To vehicle (metal) body
5 . Red
(Connect this lead only when this unit
is used as STA
N D AL ONE mode.)
To electric terminal controlled by
ignition switch (12 V DC)
ON/OFF .
.
14. P arking brake switch
12. P ower supply side
11. Light green
U sed to detect the ON/OFF status of
the parking brake. This lead must be
connected to the power supply side of
the parking brake switch.
4. F use resistor
13. G round side
7. Connection method
8 . Clamp the lead. 9 . Clamp firmly with
needle-nosed pliers.
10. Note:
• The position of the parking brake switch depends
on the vehicle model.
F or details, consult the
vehicle O wner ’ s M anual or dealer.
Fig. 17
±∑ qJA«