Pioneer ELITE VSX-LX304 Instruction Manual Download Page 23

Page: 23 / 180

≫

≫

≫

≫

≫

≫

❏

Ceiling Speakers Installation Example

a: 30° to 55°, b: 65° to 100°, c: 125° to 150°

This is a system with the basic 5.1 channel system (

p19

) consisting of front

speakers, a center speaker, surround speakers and a powered subwoofer, and

added top front speakers or top middle speakers or top rear speakers combined.

Installing the height speakers will enrich the sound field feeling in the upper

space. Install the top front speakers on the ceiling anterior to the seating position,

top middle speakers on the ceiling directly above the seating position, and top

rear speakers on the ceiling posterior to the seating position. The distance

between each pair should match the distance between the front speakers.

• Dolby Laboratories recommends the setups of these types of height speakers

to obtain the best Dolby Atmos effect.

7,8 Height Speakers

Choose one of the following:

• Top Front Speakers

• Top Middle Speakers

• Top Rear Speakers

❏

Speaker Layouts and Selectable Listening

Modes (

p106

)

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands