Pioneer ELITE VSX-LX304 Instruction Manual Download Page 169

Page: 169 / 180

169

≫

≫

≫

≫

≫

≫

Tuner

❏

Poor reception or much noise

• Recheck the antenna connection.

•

Move the antenna away from the speaker cord or power cord.

•

Move the unit away from your TV or PC.

•

Passing cars or airplanes in the vicinity can cause interference.

•

If radio waves are blocked by concrete walls, etc., radio reception may be poor.

• Change the reception mode to mono (

p89

• Operating the remote controller during AM reception may cause noise.

•

FM reception may be clearer if you use the antenna jack on the wall used for the TV.

(

p60

)

BLUETOOTH function

•

Unplug and plug the power cord of the unit, or turn off and on the BLUETOOTH-enabled device. Restart of the BLUETOOTH-enabled device may

be effective.

•

BLUETOOTH-enabled devices must support the A2DP profile.

•

Because a radio wave interference will occur, this unit may not be used near devices such as a microwave oven or cordless phone which use the

radio wave in the 2.4 GHz range.

•

A metallic object near the unit can affect on the radio wave, and BLUETOOTH connection may not be possible.

Check the following if the problem persists after you have confirmed the above.

❏

Cannot connect with this unit

•

Check if the BLUETOOTH function of the BLUETOOTH-enabled device is enabled.

(

p155

)

❏

Music playback is unavailable on the unit even after successful BLUETOOTH connection

•

When the audio volume of your BLUETOOTH-enabled device is set low, the audio may not be played back. Turn up the volume of the

BLUETOOTH-enabled device.

•

Depending on the BLUETOOTH-enabled device, the Send/Receive selector switch may be equipped. Select Send mode.

•

Depending on the characteristics or specifications of the BLUETOOTH-enabled device, music may not be played back on this unit.

❏

Sound is interrupted

•

There may a problem with the BLUETOOTH-enabled device. Check the information on a web page.

❏

The audio quality is poor after connection with a BLUETOOTH-enabled device

•

The BLUETOOTH reception is poor. Move the BLUETOOTH-enabled device closer to the unit, or remove any obstacle between the

BLUETOOTH-enabled device and this unit.

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands