Pioneer ELITE VSX-LX304 Instruction Manual Download Page 133

Page: 133 / 180

133

≫

≫

≫

≫

≫

≫

Dolby

Change the setting of when Dolby signals are input.

Setting Item

Default Value

Setting Details

Loudness

Management

When playing Dolby TrueHD, enable the dialog

normalization function which keeps the volume of

dialog at a certain level. Note that when this setting

is Off, the Midnight function that allows you to enjoy

surround at low volumes is fixed to off when playing

Dolby Digital Plus/Dolby TrueHD.

"On": When this function is used

"Off": When this function is not used

Center Spread*

Off

Adjust the width of the sound field of the front

channel when playing in Dolby Audio - Surr

listening mode.

"On": The sound field is spread to left and right.

"Off": The sound field is centralized.

•

Depending on the speaker settings, "Off" is

applied.

This function will not be selectable if the firmware is updated after purchase or the

firmware is switched in the product production process. For details of firmware update,

see "Additional Function (Firmware Update)"

(

DTS

Change the setting of when DTS signals are input.

Setting Item

Default Value

Setting Details

Dialog Control

0 dB

You can increase the volume of dialog portion of

the audio up to 6 dB by 1 dB step so that you can

hear the dialog easily in noisy atmosphere.

• This cannot be set for content other than DTS:X.

• Depending on the content, this function may not

be selected.

Volume

Change the Volume settings.

Setting Item

Default Value

Setting Details

Mute Level

-∞ dB

Set the volume lowered from the listening volume

when muting is on. Select a value from "-∞ dB",

"-40 dB" and "-20 dB".

Volume Limit

Off

Set the maximum value to prevent the volume

from becoming too loud. Select a value from "Off",

"-32 dB" to "+17 dB".

Power On Level

Last

Set the volume level of when the power is turned

on. Select a value from "Last" (Volume level before

entering standby mode), "-∞ dB", and "-81.5 dB" to

"+18.0 dB".

•

You cannot set a higher value than that of

"Volume Limit".

Headphone Level 0.0 dB

Adjust the output level of headphones. Select a

value between "-12.0 dB" and "+12.0 dB".

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands