Pioneer ELITE VSX-LX304 Instruction Manual Download Page 100

Page: 100 / 180

100

≫

≫

≫

≫

≫

≫

Adjusting the tone

Adjusting TREBLE/BASS

You can adjust the sound quality of the speakers.

Press TONE repeatedly to select Treble or Bass and adjust the content.

Treble: Enhances or moderates the high-tone range of the speakers.

Bass: Enhances or moderates the low-tone range of the speakers.

Press + or - for adjustment.

Adjusting DIALOG

Emphasizes movie lines and music vocals to listen to them more easily. It is

effective to movie lines in particular. Also, it exerts the effect even if the center

speaker is not used. Select a desired level from "1" (low) to "5" (high).

1. Press DIALOG.

Press + or - for adjustment.

• Depending on the input source or listening mode setting, selection is not

possible, or the desired effect may not be achieved.

TONE

DIALOG

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands