background image

4

En

Detach the front panel to prevent theft. Remove any cables and devices attached to the 
front panel and turn off the unit before detaching it.

 Important

Avoid subjecting the front panel to excessive shock.

Keep the front panel out of direct sunlight and high temperatures.

Always store the detached front panel in a protective case or bag.

Remove the insulation sheet before use.

Appears when the sound retriever function is set (page 8).

Appears when random play is set.

Appears when repeat play is set.

Detaching the front panel

Preparing the remote control

Indication

Description

Detach

Attach

How to replace the battery

Insert the CR2025 (3 V) battery with the plus (+) and 
minus (–) poles orientated properly.

 WARNING

Do not ingest the battery, Chemical Burn Hazard.
(The remote control supplied with) This product contains a coin/button cell battery. If the coin/
button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to 
death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from 
children.
If you think batteries might have been swallowed or placed inside any part of the body, seek 
immediate medical attention.

Do not expose the battery or remote control to excessive heat such as direct sunlight or fire.

 CAUTION

There is a potential danger of explosion if the battery is incorrectly replaced. When replacing the 
battery, replace it with the same type.

Do not handle or store the battery with metallic tools or objects.

If the battery leaks, remove the battery and wipe the remote control completely clean. Then install a 
new battery.

When disposing of used batteries, please comply with governmental regulations or environmental 
public institutions’ rules that apply in your country/area.

 Important

Do not store the remote control in high temperatures or direct sunlight.

Do not let the remote control fall onto the floor, where it may become jammed under the brake or 
accelerator pedal.

When you turn the ignition switch to ON after installation, [SET UP :YES] appears in the 
display.

1

Press the 

M.C.

 dial.

The setup menu disappears after 30 seconds of no operation. If you prefer not to set 
at this time, turn the 

M.C.

 dial to select [NO], then press to confirm.

2

Turn the 

M.C.

 dial to select the options, then press to confirm.

To proceed to the next menu option, you need to confirm your selection. 

Setup menu

Menu Item

Description

CLOCK SET

Set the clock.

FM STEP

Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

AM STEP

Select the AM tuning step from 10 kHz or 9 kHz.

[10], [9]

Summary of Contents for DEH-S1190UB

















Reviews: