Installation
<ENGLISH>
Note:
• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver’s
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• The semiconductor laser will be damaged if it
overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.
• If installation angle exceeds 60° from horizontal,
the unit might not give its optimum performance.
(Fig. 4)
Fig. 4
• The cords must not cover up the area shown in the
figure below. This is necessary to allow the ampli-
fires to radiate freely. (Fig. 5)
Fig. 5
60
°
Connecting the Units
<ENGLISH>
+
≠
+
≠
+
≠
+
≠
+
≠
+
≠
+
≠
+
≠
+
≠
+
≠
Left
Right
Fuse resistor
Fuse resistor
Fuse holder
Perform these connections when using
the optional amplifier.
With a 2 speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.
Yellow/black
If you use a cellular telephone, connect
it via the Audio Mute lead on the
cellular telephone. If not, keep the
Audio Mute lead free of any
connections.
Yellow
To terminal always supplied with
power regardless of ignition switch
position.
Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
Gray
Gray/black
Violet
Violet/black
White
White/black
Green
Green/black
Connecting cords with RCA pin
plugs (sold separately)
Power amp
(sold separately)
System remote control
Power amp
(sold separately)
Power amp
(sold separately)
Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300
mA 12 V DC).
Low range output
(LOW/SUBWOOFER OUTPUT)
Middle range output
(MID/REAR OUTPUT)
High range output
(HIGH/FRONT OUTPUT)
Middle range speaker
High range speaker
Low range speaker
High range speaker
High range speaker
High range speaker
Middle range speaker
Middle range speaker
Middle range speaker
Low range speaker
External amp is required for
connecting the low range speaker.
23 cm (9 in.)
15 cm (5-7/8 in.)
DSP switch
Switch the DSP switch
as illustration below.
Antenna jack
15 cm (5-7/8 in.)
IP-BUS input
(Blue)
Multi-CD player
(sold separately)
IP-BUS cable
This product
Jack for the Wired Remote Control
Refer to Wired Remote Control’s manual
(sold separately).
This terminal may or may
not be included.
Fig. 3
Connection diagram for 3-way network mode
DIN Front/Rear-mount
This unit can be properly installed either from “Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush (Fig. 6)
Fig. 6
182
53
Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly possible using the top
and bottom tabs. To secure, bend the
tabs 90 degrees.)
Dashboard
Rubber bush
Screw
CRD3829AN 03.12.8 7:51 PM Page 5
