Pioneer DEH-P6800MP, Service Manual

Page: 54 / 80

DEH-P680MP/XN/UC
54
1 2 3 4
1 2 3 4
C
D
F
A
B
E
[Key]
Contents
Display
[4] + [6] + Reset or
[4] + [6] + BU + ACC
Test Mode In
[CD] or [SOURCE]
Source On
TRK MIN SEC
[BAND]
Power On
(T.Offset is adjusted)
TRK MIN SEC
00 00 00
[3]
Power On
(T.Offset is not adjusted)
99 99 99
[2]
RF AMP
Gain switching
GG GG GG
*1
[4]
SPINDLE
Speed switching
SP SP SP
*9
[3]
Focus Close
S curve check
TRK MIN SEC
91 91 91
[6]
Focus Mode switching
0X 0X 0X
*2
[1]
Tracking Servo
Close
00 00 00
or 99 99 99
[>]
CRG +
[2]
Self-adjusting
switching
TRK MIN SEC
?? ?? ??
*3 *8
[<]
CRG -
*8
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[1]
T.Close & AGC
Applicable servomechanism
TRK MIN SEC
?tr ?min ?sec
[6] [3]
RF AGC /
RF AGC coefficient display
[>]
CRG +
8X 8X 8X
or 9X 9X 9X
[2]
T.Balance adjustment /
T.BAL coefficient display
TRK MIN SEC
?? ?? ??
[<]
CRG - T.Close
Applicable servomechanism
?? ?? ??
[1]
F,T,RF AGC
F.Bias display switching
TRK MIN SEC
TRK MIN SEC
TRK MIN SEC
TRK MIN SEC
?tr ?min ?sec
TRK MIN SEC
[3] [6]
CRG/TR jump
value switching
[>]
CRG/TR Jump +
[2]
Tracking Open
[<]
CRG/TR Jump -
?tr ?min ?sec
TRK MIN SEC
TRK MIN SEC
TRK MIN SEC
?tr ?min ?sec
00 00 00
or 99 99 99
TRK MIN SEC
TRK MIN SEC
?tr ?min ?sec
8X 8X 8X
or 9X 9X 9X
8X 8X 8X
or 9X 9X 9X
00 00 00
or 99 99 99
TRK MIN SEC
?tr ?min ?sec ?? ?? ??
*7
F,T AGC / F.Bias
RF AGC
8X 8X 8X
or 9X 9X 9X
[2]
Tracking Open
*6
*5
*4 *4
Operation
[Key] Test Mode
[BAND] Power On/Off
[>]
CRG + / TR Jump +
(Direction of the external surface)
[<]
CRG - / TR Jump -
(Direction of the internal surface)
[1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
[2] RF Gain switching / Offset adjustment display /
T.Balance adjustment / T. Open
[3] F. Close,S Curve / Rough Servo and RF AGC /
F,T,RF AGC
[4]
SPDL 1X/2X switching
As for the double speed(2x), audio output cannot be
supported.
[5]
Error Rate measurement
ON : ERR 30Counts Start
BER display data[%]
[6] F. Mode switching / Tracking Close / CRG•TR
Jump Switching
*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
• In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
*10
TRK MIN SEC
[5]
Gop Mode
Gop Mode switching
OL OL OL
*1) TYP
→
+ 6 dB
→
+ 12 dB
TRK MIN SEC TRK
06
MIN
06
SEC
06
TRK
12
MIN
12
SEC
12
*2) Focus Close
→
S Curve check setting
→
F EQ measurement setting
TRK
00
MIN
00
SEC
00
TRK
01
MIN
01
SEC
01
TRK
02
MIN
02
SEC
02
(
TRK
99
MIN
99
SEC
99)
*3) F.Offset Display
→
RF.Offset
→
T.Offset Display
→
Switch to the
order of the original display
*4) 1TR/4TR/10TR/32TR/100TR
*5) Single
→
4TR
→
10TR
→
32TR
→
100TR
→
CRG Move
9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86)
*6) Only at the time of CRG move, 100TR jump
*7) TRK/MIN/SEC
→
F.AGC
→
T.AGC Gain
→
F.Bias
→
RF AGC
*8) CRG motor voltage = 2 [V]
*9) TYP (1X)
→
2X
→
1X
TRK MIN SEC TRK
22
MIN
22
SEC
22
TRK
11
MIN
11
SEC
11
*10) OFF(TYP)
→
FORCUS
→
TRACKING
TRK MIN SEC TRK
70
MIN
70
SEC
70
TRK
71
MIN
71
SEC
71
• As for the double speed (2x), audio output cannot be supported
Note)Test mode should use the key of remote control.