background image

<ENGLISH>

Installation

Note:
• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts
can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications
of the vehicle.

• Install the unit where it does not get in the driver’s

way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot —
for instance, near a heater outlet.

• If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.
(Fig. 3)

Fig. 3

60

°

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 4)

Fig. 4

Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)

182

53

Rubber bush

Screw

Dashboard

Removing the Unit (Fig. 5) (Fig. 6)

Fig. 5

Fig. 6

5

6

Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)

Frame

About the fixing screws for the front panel

If you do not operate the Detaching and Replacing the Front Panel Function, use the sup-
plied fixing screws and fix the front panel to this unit.

Fig. 10

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 7)

Fig. 7

2. Fastening the unit to the factory radio mounting bracket. 

(Fig. 8) (Fig. 9)

Select a position where the screw holes of the bracket and
the screw holes of the head unit become aligned (are fitted),
and tighten the screws at 2 places on each side. Use either
truss screws (5 

×

8 mm) or flush surface screws 

(5 

×

9 mm), depending on the shape of the screw holes in

the bracket

.

Fig. 8

Fig. 9

11

13

12

10

8

9

Frame

Screw

Dashboard or Console

Factory radio mounting bracket

Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)

Insert the supplied extraction keys
into the unit, as shown in the figure,
until they click into place. Keeping
the keys pressed against the sides of
the unit, pull the unit out.

Fixing screw

Summary of Contents for DEH-P43

Page 1: ...sed speaker leads without fail There is a possi bility of short circuiting if the leads are not insulat ed To prevent incorrect connection the input side of the IP BUS connector is blue and the output side is black Connect the connectors of the same colors correctly If this unit is installed in a vehicle that does not have an ACC accessory position on the ignition switch the red lead of the unit s...

Page 2: ...bend them Install as firmly as possible using the top and bottom tabs To secure bend the tabs 90 degrees 182 53 Rubber bush Screw Dashboard Removing the Unit Fig 5 Fig 6 Fig 5 Fig 6 5 6 Insert the release pin into the hole in the bottom of the frame and pull out to remove the frame When reattaching the frame point the side with a groove downwards and attach it Frame About the fixing screws for the...

Page 3: ...ant excessive et un mauvais fonction nement de l appareil Pour éviter les courts circuits recouvrez les fils déconnectés par du ruban isolant En particulier n oubliez pas d isoler les fils d enceintes Un court circuit peut se produire si les fils ne sont pas isolés Pour éviter une connexion incorrecte le côté entrée du connecteur IP BUS est bleu et même couleur cor rectement Si cette unité est ins...

Page 4: ...es en fonction de l épaisseur du matériau du tableau de bord et courbez les Assurez le maintien aussi solidement que possible en utilisant les languettes inférieures et supérieures Cela fait courbez les languettes de 90 degrés Bague en caoutchouc Vis Tableau de bord Dépose de l unite Fig 5 Fig 6 Fig 5 Fig 6 5 6 Cabre Introduisez le tige de déblocage bans l orifice du fond du cabre et tirez pour en...

Reviews: