Pioneer DEH-7350BT, Owner'S Manual

Page: 9 / 108

!
The phone book in your cellular phone will be
transferred automatically when the phone is
connected to this unit.
!
Depending on the cellular phone, the phone
book may not be transferred automatically. In
this case, operate your cellular phone to trans-
fer the phone book. The visibility of this unit
should be on. Refer to
VISIBLE (setting the visi-
bility of this unit) on the previous page.
1
Press M.C. to display SEARCH (alphabetical
list).
2
Turn M.C. to select the first letter of the name
you are looking for.
!
Press and hold M.C. to select the desired
character type.
3
Press
M.C.
to display a registered name list.
4
Turn M.C. to select the name you are looking
for.
5
Press M.C. to display the phone number list.
6
Turn M.C. to select a phone number you want
to call.
!
When you find a phone number that you
want to store in memory, press and hold
one of the preset tuning buttons (
1 to 6 ).
!
Press one of preset buttons 1 to 6 to recall
the desired preset number.
7
Press M.C. to make a call.
PRESET
(preset phone numbers)
1
Press M.C. to display the setting mode.
2
Use M.C. to select the desired preset number.
Turn to change the menu option. Press to se-
lect.
!
You can also press one of the preset num-
ber buttons
1 to 6 to select a number.
3
Press M.C. to make a call.
PHONE FUNC (phone function)
You can set A. ANSR and RING TONE from this
menu. For details, refer to Function and operation
on this page.
Function and operation
1 Display PHONE FUNC.
Refer to
PHONE FUNC
(phone function) on this
page.
2 Press M.C. to display the function menu.
3 Turn M.C. to select the function.
After selecting, perform the following proce-
dures to set the function.
A. ANSR (automatic answering)
1
Press M.C. to turn automatic answering on or
off.
RING TONE (ring tone select)
1
Press M.C. to turn the ring tone on or off.
Audio Adjustments
1 Press M.C. to display the main menu.
2 Turn M.C. to change the menu option
and press to select AUDIO.
3 Turn M.C. to select the audio function.
After selecting, perform the following proce-
dures to set the audio function.
FAD/BAL (fader/balance adjustment)
1
Press
M.C.
to display the setting mode.
2
Press M.C. to cycle between fader (front/rear)
and balance (left/right).
3
Turn M.C. to adjust speaker balance.
!
When the rear output and RCA output setting
are
SW
, you cannot adjust front/rear speaker
balance. Refer to SW CONTROL (rear output
and subwoofer setting) on the next page.
EQUALIZER (equalizer recall)
1
Press
M.C.
to display the setting mode.
2
Turn M.C. to select the equalizer.
DYNAMIC
—
VOCAL
—
NATURAL
—
CUSTOM
—
FLAT
—
POWERFUL
3
Press M.C. to confirm the selection.
TONE CTRL (equalizer adjustment)
!
Adjusted equalizer curve settings are stored in
CUSTOM .
1
Press M.C. to display the setting mode.
2
Press M.C. to select BASS (bass)/ MID (mid)/
TREBLE (treble).
3
Turn
M.C.
to adjust the level.
Adjustment range:
+6
to
-6
LOUDNESS
(loudness)
Loudness compensates for deficiencies in the low-
and high-frequency ranges at low volume.
1
Press M.C. to display the setting mode.
2
Turn M.C. to select the desired setting.
OFF (off)
—
LOW (low)
—
HIGH (high)
3
Press M.C. to confirm the selection.
SUBWOOFER1 (subwoofer on/off setting)
This unit is equipped with a subwoofer output
which can be turned on or off.
1
Press M.C. to display the setting mode.
2
Turn
M.C.
to select the desired setting.
NORMAL (normal phase)
—
REVERSE (reverse
phase)
—
OFF (subwoofer off)
3
Press M.C. to confirm the selection.
SUBWOOFER2 (subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1
Press M.C. to display the setting mode.
2
Press M.C. to cycle between the cut-off fre-
quency and output level of the subwoofer.
Cut-off frequency (Cut-off frequency display
flashes.)
—
Output level (Output level display
flashes.)
3
Turn M.C. to select the desired setting.
Cut-off frequency: 50HZ
—
63HZ
—
80HZ
—
100HZ
—
125HZ
Output level:
-24
to
+6
SLA
(source level adjustment)
SLA (Source Level Adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
!
Settings are based on the FM volume level,
which remains unchanged.
!
The AM volume level can also be adjusted with
this function.
!
When selecting FM as the source, you cannot
switch to
SLA .
1
Press M.C. to display the setting mode.
2
Turn
M.C.
to adjust the source volume.
Adjustment range: +4 to
–
4
3
Press M.C. to confirm the selection.
Initial Settings
1 Press S (SRC/OFF) and hold until the unit
turns off.
2 Press M.C. and hold until function name
appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
English
Operating this unit
9
Section
Operating this unit
En
02