Pioneer CD RDS DEH-73BT, Owner'S Manual

Page: 10 / 64

1
Press
M.C.
to display the setting mode.
2
Turn M.C. to select the equalizer.
DYNAMIC
—
VOCAL
—
NATURAL
—
CUSTOM
—
FLAT
—
POWERFUL
3
Press M.C. to confirm the selection.
TONE CTRL (equalizer adjustment)
!
Adjusted equalizer curve settings are stored in
CUSTOM .
1
Press M.C. to display the setting mode.
2
Press M.C. to select BASS (bass)/ MID (mid)/
TREBLE (treble).
3
Turn
M.C.
to adjust the level.
Adjustment range:
+6
to
-6
LOUDNESS
(loudness)
Loudness compensates for deficiencies in the low-
and high-frequency ranges at low volume.
1
Press M.C. to display the setting mode.
2
Turn M.C. to select the desired setting.
OFF (off)
—
LOW (low)
—
HIGH (high)
3
Press M.C. to confirm the selection.
SUBWOOFER1 (subwoofer on/off setting)
This unit is equipped with a subwoofer output
which can be turned on or off.
1
Press M.C. to display the setting mode.
2
Turn
M.C.
to select the desired setting.
NORMAL (normal phase)
—
REVERSE (reverse
phase)
—
OFF (subwoofer off)
3
Press M.C. to confirm the selection.
SUBWOOFER2 (subwoofer adjustment)
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1
Press M.C. to display the setting mode.
2
Press M.C. to cycle between the cut-off fre-
quency and output level of the subwoofer.
Cut-off frequency (Cut-off frequency display
flashes.)
—
Output level (Output level display
flashes.)
3
Turn M.C. to select the desired setting.
Cut-off frequency: 50HZ
—
63HZ
—
80HZ
—
100HZ
—
125HZ
Output level:
-24
to
+6
SLA
(source level adjustment)
SLA (Source Level Adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
!
Settings are based on the FM volume level,
which remains unchanged.
!
The AM volume level can also be adjusted with
this function.
!
When selecting FM as the source, you cannot
switch to
SLA .
1
Press M.C. to display the setting mode.
2
Turn
M.C.
to adjust the source volume.
Adjustment range: +4 to
–
4
3
Press M.C. to confirm the selection.
Initial Settings
1 Press and hold S (SRC/OFF) until the unit
turns off.
2 Press M.C. and hold until function name
appears in the display.
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
CLOCK SET (setting the clock)
1
Press M.C. to display the setting mode.
2
Press
M.C.
to select the segment of the clock
display you wish to set.
Hour
—
Minute
3
Turn M.C. to adjust the clock.
AUX (auxiliary input)
Activate this setting when using an auxiliary de-
vice connected to this unit.
1
Press M.C. to turn AUX on or off.
USB (plug and play)
This setting allows you to switch your source to
USB / iPod automatically.
1
Press M.C. to turn the plug and play function
on or off.
ON
–
When a USB storage device/iPod is con-
nected, depending on the type of device, the
source is automatically switched to
USB / iPod
when you turn on the engine. If you disconnect
your USB storage device/iPod, this unit
’
s
source is turned off.
OFF
–
When a USB storage device/iPod is con-
nected, the source is not switched to USB /
iPod automatically. Please change the source
to USB / iPod manually.
SW CONTROL (rear output and subwoofer set-
ting)
The rear speaker leads output and RCA output
can be used for full-range speaker or subwoofer
connection.
If you switch to
REAR-SP
:
SW
, you can connect a
rear speaker lead directly to a subwoofer without
using an auxiliary amp.
Initially,
REAR-SP is set for rear full-range speaker
connection (
FUL
).
1
Press
M.C.
to display the setting mode.
2
Turn M.C. to change the output and press to
select.
REAR-SP
—
PREOUT
3
Turn M.C. to change the setting.
REAR-SP
:
FUL
—
SW
PREOUT : SW
—
REA
!
Even if you change this setting, there will
be no output unless you turn the sub-
woofer output on (refer to
SUBWOOFER1
(subwoofer on/off setting) on this page).
!
If you change this setting, subwoofer out-
put in the audio menu will return to the fac-
tory settings.
DEMO (demo display setting)
1
Press M.C. to turn the demo display on or off.
SCROLL (scroll mode setting)
When ever scroll is set to ON, recorded text infor-
mation scrolls continuously in the display. Set to
OFF if you prefer the information to scroll just
once.
1
Press M.C. to turn the ever scroll on or off.
BT CLEAR
(resetting the Bluetooth wireless tech-
nology module)
Operating this unit
02
10
Section
Operating this unit
En