Pioneer AVH-X6800DVD, Owner'S Manual

Page: 40 / 204

40
Adjusting source levels
SLA (source level adjustment) lets you adjust the volume level of
each source to prevent radical changes in volume when switch-
ing between sources.
p
Settings are based on the FM tuner volume level, which
remains unchanged.
p
This function is not available when the FM tuner is selected
as the AV source.
1 Compare the FM tuner volume level with the
level of the source.
2 Display the “ Audio ” setting screen.
 Refer to Displaying the “ Audio ” setting screen on page 40
3 Touch [ Source Level Adjuster ].
4 Touch or to adjust the source volume.
p
If you directly touch the area where the cursor can be moved,
the
SLA
setting will be changed to the value of the touched
point.
p
“
+4
” to “
–4
” is displayed as the source volume is increased
or decreased.
p
The default setting is “
0
”.
Using the auto level control
This function corrects automatically the audio level difference
between the music files or the sources.
1 Display the “
Audio
” setting screen.
 Refer to Displaying the “
Audio
” setting screen on page 40
2 Touch [ Automatic Level Control ].
3 Touch the item.

Off
(default):
Turns the auto level control setting off.

Mode1
:
Corrects a little the audio level difference between the music
files or the sources (for the narrow dynamic range audio
signal).

Mode2
:
Corrects widely the audio level difference between the
music files or the sources (for the wide dynamic range audio
signal).
Adjusting loudness
This function compensates for deficiencies in the low-frequency
and high-frequency ranges at low volume.
The default setting is “
Off
”.
Displaying the firmware
version
1 Display the “ System ” setting screen.
 Refer to Displaying the “ System ” setting screen on page
37
2 Touch [
System Information
].
3 Touch [
Firmware Information
].
The “
Firmware Information
” screen appears.
Displaying the open source
licenses
1 Display the “ System ” setting screen.
 Refer to Displaying the “ System ” setting screen on page
37
2 Touch [
System Information
].
3 Touch [ License ].
The open source licenses of the functions that this product is
equipped with appear.
Updating firmware
CAUTION

The USB storage device for updating must contain only the
correct update file.
 Never turn this product off, disconnect the USB storage
device while the firmware is being updated.
 You can only update the firmware when the vehicle is
stopped and the parking brake is engaged.
1 Download the firmware update files.
2 Connect a blank (formatted) USB storage
device to your computer, and then locate the
correct update file and copy it onto the USB
storage device.
3 Connect the USB storage device to this
product.
4 Turn the source off.

Refer to Selecting a source on page 13
5 Display the “ System ” setting screen.
 Refer to Displaying the “ System ” setting screen on page
37
6 Touch [
System Information
].
7 Touch [ Firmware Update ].
8 Touch [ Continue ] to display the data transfer
mode.
p
Follow the on-screen instructions to finish updating the
firmware.
p
This product will reset automatically after the firmware
update is completed if the update is successful.
p
If an error message appears on the screen, touch the display
and perform the above steps again.
Displaying the “Audio” setting
screen
1 Press .
2 Touch , and then
.
The “ Audio ” setting screen appears.
Using fader/balance adjustment
1 Display the “ Audio ” setting screen.
 Refer to Displaying the “ Audio ” setting screen on page 40
2 Touch [ Fader/Balance ].
p
Only the balance can be adjusted when “ Network Mode ” is
selected as the speaker mode. Touch [
Balance
] and skip to
step 4.
3 Touch or to adjust the front/rear speaker
balance.
p
Set “ Front ” and “ Rear ” to “ 0 ” when using a dual speaker
system.
4 Touch or to adjust the left/right speaker
balance.
 You can also set the value by dragging the point
on the displayed table.
Switching sound muting/
attenuation
You can automatically mute or attenuate the AV source volume
and the iPhone application volume when the navigation outputs
the guidance voice.
1 Display the “ Audio ” setting screen.

Refer to Displaying the “ Audio ” setting screen on page 40
2 Touch [
Mute Level
].
3 Touch the item.

ATT (default):
The volume becomes 20 dB lower than the current volume.

Mute :
The volume becomes 0.

Off :
The volume does not change.
Audio adjustments
40 < CRD4918-A > < CRD4918-A >
System settings Audio
adjustments
Audio adjustments